Installation guide
following
installation
steps.
To
Remove
Warming
Drawer:
1.
Open
drawer
to
its
fully
open
position.
2.
Locate
the
black loops
on
both
sides
of
the
drawer.
A.
Loop
3.
Pull
both
loops
forward
at
the
same
time,
then
pull
drawer
out
another
inch.
4.
Holding
the
drawer
by
its
sides,
not
its
front,
gently
pull
it
all
the
way
out.
To
Remove
Storage
Drawer:
1.
Pull
drawer
straight
out
to
the
first
stop.
2.
Lift
up
the
back
of
the
drawer
and
pull
out.
the
lower
section
of
the
range.
This
will
be
necessary
for
some
of
the
oy
Fogg
bow
Pay
yy
beg
OS
yee
IMPORTANT:
On
models
with
a
warming
drawer,
the
rear
range
foot
must
be
viewed
from
the
front
and
slightly
to
one
side
of
the
range.
1.
To
check
that
the
anti-tip
bracket
is
installed,
use
a
flashlight
and
look
underneath
the
bottom
of
the
range.
mg
Look
for
the
anti-tip
bracket
securely
attached
to
floor.
m_
Slide
range
back
so
rear
range
foot
is
under
anti-tip
bracket.
1.
Place
rack
in
oven.
2.
Place
level
on
rack
and
check
levelness
of
the
range,
first
side
to
side;
then
front
to
back.
3.
Ifrange
is
not
level,
pull
range
forward
until
rear
leveling
leg
is
removed
from
the
anti-tip
bracket.
Use
a
wrench
or
pliers
to
adjust
leveling
legs
up
or
down
until
the
range
is
level.
Push
range
back
into
position.
Check
that
rear
leveling
leg
is
engaged
in
the
anti-tip
bracket.
NOTE:
Range
must
be
level
for
satisfactory
baking
performance.
AWARNING
Explosion
Hazard
Use
a
new
CSA
International
approved
gas
supply
line.
Install
a
shut-off
valve.
Securely
tighten
all
gas
connections.
If
connected
to
LP,
have
a
qualified
person
make
sure
gas
pressure
does
not
exceed
14"
(36
cm) water
column.
Examples
of
a
qualified
person
include:
licensed
heating
personnel,
authorized
gas
company
personnel,
and
authorized
service
personnel.
Failure
to
do
so
can
result
in
death,
explosion,
or
fire.
Typical
rigid
pipe
connection
A
combination
of
pipe
fittings
must
be
used
to
connect
the
range
to
the
existing
gas
line.
Your
connections
may
be
different,
according
to
the
supply
line
type,
size
and
location.
1.
Apply
pipe-joint
compound
made
for
use
with
LP
gas
to
all
pipe
thread
connections.
2.
Using
a
pipe
wrench
to
tighten,
connect
the
gas
supply
to
the
range.
F
é
Cc
roa
clio
i
H
l
G
A.
Gas
pressure
regulator
F.
Manual
gas
shutoff
valve
B.
90°
elbow
(must
have
G.
¥%"
or
%" gas
pipe
Ye"
male
pipe
thread)
H.
Nipple
C.
Nipple
I.
Union
D.
Union
J.
90°
elbow
E.
Black
iron
pipe
11