Installation guide
Check
Operation
of
Oven
Bake
Burner
Check
Operation
of
Oven
Broil
Burner
1.
Remove
the
oven
rack.
Remove
the
bake
burner
cover
and
1.
Close
the
oven
door.
place
it
on
a
covered
surface.
2.
Press
the
BROIL
pad.
“FULL
BROIL”
and
broil
temperature
2.
Push
the
BAKE
pad.
Default
temperature
appears
in
the
will
appear
in
the
temperature
display.
temperature
display.
3.
Press
the
START
pad.
“ON”
indicator
will
light.
3.
Press
the
START
pad.
“Preheating”
and
“Lo”
(or
actual
The
oven
burner
should
light
within
8
seconds,
under
certain
temperature)
will
appear
in
the
temperature
display.
conditions
it
may
take
the
burner
up
to
50
to
60
seconds
to
The
oven
bake
burner
should
light
within
8
seconds,
under
light.
On
some
models,
an
electric
halo
element
also
turns
on.
certain
conditions
it
may
take
the
burner
up
to
50
to
60
seconds
to
light.
Electronic
igniters
are
used
to
light
the
bake
and
broil
burners.
A.
Oven
bake
burner
cover
A.
Gas
burner
B.
Flame
spreader
B.
Electric
halo
element
C.
Oven
bake
burner
NOTE:
Oven
door
must
be
shut
for
broil
burner
to
operate.
Adjust
Bake
FI
if
needed
just
Oven
Bake
Flame
(if
needed)
Adjust
Oven
Broil
Burner
Flame
(if
needed)
1.
Remove
access
cover
plate
(2
screws)
located
on
the
upper
wall,
inside
the
storage
or
warming
drawer
compartment.
Look
through
oven
window
to
check
broil
burner
for
proper
flame.
This
flame
should
have
a
¥2"
(1.3
cm)
long
inner
cone
of
2.
Check
the
oven
bake
burner
for
proper
flame.
bluish-green,
with
an
outer
mantle
of
dark
blue,
and
should
be
This
flame
should
have
a
¥2"
(1.3
cm)
long
inner
cone
of
clean
and
soft
in
character.
No
yellow
tips,
blowing
or
lifting
of
bluish-green,
with
an
outer
mantle
of
dark
blue,
and
should
flame
should
occur.
be
clean
and
soft
in
character.
No
yellow
tips,
blowing
or
lifting
of
flame
should
occur.
3.
Ifthe
oven
bake
flame
needs
to
be
adjusted,
locate
the
air
shutter
near
the
center
rear
of
the
range.
Use
a
flat-blade
screwdriver
to
loosen
the
locking
screw.
Rotate
the
air
shutter
until
the
proper
flame
appears.
Tighten
locking
screw.
Bown.
A.
Locking
screw
B.
Air
shutter
A.
Air shutter
If
flame
needs
to
be
adjusted:
B.
Locking
screw
1.
Use
a
flat-blade
screwdriver
to
loosen
the
locking
screw
on
the
air
shutter
located
at
the
rear
of
the
broil
burner.
4.
Push
CANCEL/OFF
pad.
2.
Adjust
the
air
shutter
as
need.
5.
Reinstall
oven
bake
burner
access
plate.
3.
Tighten
lock
screw.
14