Installation guide
To
Convert
Standard
Surface
Burners
1.
Remove
burner
cap.
2.
Using
a
T20
Torx®
screwdriver,
remove
the
burner
base.
3.
Apply
masking
tape
to
the
end
of
a 7
mm
nut
driver
to
help
hold
the
gas
orifice
spud
in
the nut
driver
while
changing
it.
Press
nut
driver
down
onto
the
gas
orifice
soud
and
remove
by
turning
it
counterclockwise
and
lifting
out.
Set
gas
orifice
spud
aside.
A.
Igniter
electrode
B.
Gas
tube
opening
C.
Burner
cap
D.
Burner
base
4.
Gas
orifice
spuds
are
stamped
with
a
number,
marked
with
1
color
dot,
and
have
a
groove
in
the
hex
area.
Replace
the
Natural
gas
orifice
spud
with
the
correct
LP
gas
orifice
spud.
A.
Groove
Refer
to
the
following
chart
for
correct
LP
gas
orifice
spud
placement.
LP
Gas
Orifice
Spud
Chart
for
Standard
Surface
Burners
Burner
Location
Burner
Rating
Color
Size
Right
front
5,000
Btu/h
Red
0.70
mm
Left
front
13,000
Btu/h
Green
1.10
mm
Right
rear
10,000
Btu/h
Blue
0.95
mm
Left
rear
5,000
Btu/h
Red
0.70
mm
5.
Place
Natural
gas
orifice
spuds
in
plastic
parts
bag
for
future
use
and
keep
with
package
containing
literature.
6.
Replace
burner
cap.
7.
Repeat
steps
1-6
for
the
remaining
burners,
except
for
the
TripleTier®
Flame
burner
(on
some
models).
See
“To
Convert
3.
Remove
the
plate
on
the
external
gas
orifice
spud.
A.
Burner
caps
B.
Burner
heads
C.
External
gas
orifice
spud
access
plate
D.
Internal
gas
orifice
spud
IMPORTANT:
The
TripleTier®
Flame
burner
has
2
gas
orifice
spuds.
Do
not
forget
to
change
the
external
gas
orifice
spud
located
under
the
plate.
A.
Plate
B.
External
gas
orifice
spud
C.
Internal
gas
orifice
spud
4.
Apply
masking
tape
to
the
end
of
a 7
mm
nut
driver
to
help
hold
the
internal
gas
orifice
spud
in
the
nut
driver
while
changing
it.
Press
nut
driver
down
onto
the
internal
gas
orifice
spud
and
remove
by
turning
it
counterclockwise
and
lifting
out.
Set
internal
gas
orifice
spud
aside.
5.
Use
a7
mm
combination
wrench
to
remove
the
external
gas
orifice
spud.
Turn
counterclockwise
to
remove.
Set
external
gas
orifice
spud
aside.
6.
Replace
each
Natural
gas
orifice
spud
with
the
correct
LP
gas
orifice
spud.
Refer
to
the
following
chart
for
correct
LP
gas
orifice
spud
placement.
LP
Gas
Orifice
Spud
Chart
for
TripleTier®
Flame
Burners
Burner
Location
Burner
Rating Color
Size
TrioleTier®
Flame
Burners”
section
Left
front
(external
11,800
Btu/h
Brown
1.00
mm
P
.
TripleTier®
burner)
To
Convert
TripleTier®
Flame
Burners
(on
some
models)
Left
front
(internal
2,200
Btus+h
=
Orange
=—-
0.42
mm
1.
Remove
burner
cap.
2.
Remove
the
burner
head
using
a
size
T20
Torx®
screwdriver.
TripleTier®
burner)
7.
Replace
burner
plate,
head
and
cap.
8.
Place
Natural
gas
orifice
spuds
in
plastic
parts
bag
for
future
use
and
keep
with
package
containing
literature.
17