Installation guide
IMPORTANT:
The
TripleTier®
Flame
burner
has
2
gas
orifice
spuds.
Do
not
forget
to
change
the
external
gas
orifice
spud
located
under
the
plate.
A..
>)
A.
Plate
B.
External
gas
orfice
spud
C.
Internal
gas
orifice
spud
4.
Apply
masking
tape
to
the
end
of
a 7
mm
nut
driver
to
help
hold
the
internal
gas
orifice
spud
in
the
nut
driver
while
changing
it.
Press
nut
driver
down
onto
the
internal
gas
orifice
spud
and
remove
by
turning
it
counterclockwise
and
lifting
out.
Set
internal
gas
orifice
spud
aside.
5.
Use
a7
mm
combination
wrench
to
remove
the
external
orifice
spud.
Turn
counterclockwise
to
remove.
Set
external
gas
orifice
spud
aside.
6.
Replace
each
LP
gas
orifice
spud
with
the
correct Natural
gas
orifice
spud.
Refer
to
the
following
chart
for
correct Natural
gas
orifice
soud
placement.
Natural
Gas
Orifice
Spud
Chart
for
TripleTier®
Flame
Burners
To
Convert
Oven
Bake
Burner
Burner
Location
Burner
Rating
Size
Left
front
(external
12,200
Btu/h
1.70
mm
TripleTier®
burner)
Left
front
(internal
2,800
Btu/h
0.70
mm
TripleTier®
burner)
7.
Replace
burner
plate,
head
and
cap.
8.
Place
LP
gas
orifice
spuds
in
plastic
parts
bag
for
future
use
and
keep
with
package
containing
literature.
20
Remove
oven
racks.
Use
a
¥%"
combination
wrench
to
loosen
the
orifice
hood
away
from
the
pin
(about
2
to
2%
turns).
The
oven
bake
burner
flame
cannot
be
properly
adjusted
if
this
conversion
is
not
made.
See
“Adjust
Oven
Bake
Flame”
in
the
“Electronic
Ignition
System”
section.
A.
Orifice
hood
B.
Pin
To
Convert
Oven
Broil
Burner
—_
Use
a
¥2"
combination
wrench
to
loosen
the
orifice
hood
away
from
the
pin
(about
2
to
2%
turns).
The
oven
broil
burner
flame
cannot
be
properly
adjusted
if
this
conversion
is
not
made.
See
“Adjust
Oven
Broil
Burner
Flame”
in
the
“Electronic
Ignition
System”
section.
A.
Locking
screw
B.
Orifice
hood
Reinstall
the
warming
or
storage
drawer.
See
the
“Replace
Oven
Racks
and
Warming
or
Storage
Drawer”
section
for
instructions.
Complete
installation.
See
“Make
Gas
Connection”
and
“Electronic
Ignition
System”
sections.
Checking
for
proper
cooktop
burner
and
oven
bake
burner
flame
is
very
important.
Natural
gas
flames
do
not
have
yellow
tips.
IMPORTANT:
You
may
have
to
adjust
“LO”
setting
for
each
cooktop
burner.