5019_719_01132_GB 1-06-2007 14:30 Pagina 1 KHPF 7510 KHPS 7510 Instructions for use
5019_719_01132_GB 1-06-2007 14:30 Pagina 2
5019_719_01132_GB 1-06-2007 14:30 Pagina 3 Product description and symbols 4 Using the burners 4 Practical advice on using the hob 5 Positioning the pan supports and wok support 5 Hood and cabinetry clearances (mm) 6 Injector table 6 Warnings and suggestions 7 Safeguarding the environment 8 Installation (Flush and Traditional fitting) 9 Gas connection 9 Electrical connection 10 Fixing the Hob to the supporting structure. Traditionally fitted model (Semi Flush fitting).
5019_719_01132_GB 1-06-2007 14:30 Pagina 4 Product description and symbols 1. 2. 3. 4. 5. 6. 7. 8. 9. Removable pan supports 1 kWh auxiliary burner 1.65 kWh semi-fast burner 1.
019_719_01132_GB 1-06-2007 14:30 Pagina 5 Practical advice on using the hob Read the instructions to get the best out of your hob. • Use pans with a similar diameter to the burner(see the table). • Use flat bottomed pans except with the wok support. • Do not use excessive water when cooking foods and use the lid. • Ensure that pans are fully supported by the pan supports and do not protrude over the edges.
5019_719_01132_GB 1-06-2007 14:30 Pagina 6 Hood and cabinetry clearances (mm) If a hood is to be installed above the hob, refer to the hood installation instructions to ensure the correct height above the hob. Note: If the distance “A” between the kitchen wall cabinets is between 600 and 730 mm, height “B" shall be at least 530 mm. If the distance “A” between the kitchen wall cabinets is wider than the hob’s width, height “B shall be at least 400 mm.
5019_719_01132_GB 1-06-2007 14:30 Pagina 7 Warnings and suggestions To get the most out of your hob, please read the instructions carefully and keep them for future consultation. • These instructions are only valid in the countries whose destination symbol is shown on the serial number plate on the hob. • The packing (plastic bags, expanded polyurethane, etc) pose a potential threat to children and should be disposed of carefully.
5019_719_01132_GB 1-06-2007 14:30 Pagina 8 Safeguarding the environment Packing The packing material is 100% recyclable and is labelled with the recycling symbol . Please dispose of all packing responsibly and carefully. Note: • Incorrect placement of the pan supports can scratch the hob. To avoid this always ensure that the rubber feet on the bottom of the pan supports are the only part of the pan supports that touch the hob and do not drag the pan supports across the hob surface.
5019_719_01132_GB 1-06-2007 14:30 Pagina 9 Installation (Flush and Semi-Flush fitting) Technical information for the installer • Warning: this is a heavy products which requires the installation to be carried out by two people. • When installing the hob it is advisable to wear protective gloves. • This appliance can be installed into a 20mm 50mm thick worktop. • If no oven is to be installed below the hob, a panel must be fitted under the hob to prevent hob damage and protect the cupboard contents.
5019_719_01132_GB 1-06-2007 14:30 Pagina 10 Electrical connection The electrical connections must comply with current legislation and be carried out by a qualified, competent person. • Information on the voltage and power absorbed are shown on the serial no. plate. • The appliance must be earthed. • When installing the appliance, we recommend that this hob is protected by a 3mm bi-polar switch.
5019_719_01132_GB 1-06-2007 14:30 Pagina 11 Fixing the Hob to the worktop. Flush fitted model. Important: The following procedure shall be carried out by competent technical personnel only. The hob can be installed on different types of materials, such as masonry, metal, bare wood and heat resistant laminate coated wood (90°C). Cut an opening into the worktop to the dimensions shown in the diagram.
5019_719_01132_GB 1-06-2007 14:30 Pagina 12 Adaption to a different type of gas supply If you are using a different kind of gas from the one indicated on the serial no. plate and the orange label on the back of the hob, you must replace the injectors; in the case of the Wok burner, adjust the primary air (see Injector table on page 6). The orange label should be removed and kept together with the manual.
5019_719_01132_GB 1-06-2007 14:30 Pagina 13 Fitting the wok burner To fit the double crown wok burner: Insert in the following order: 1. burner ring (A); 2. decorative covering ring (B); 3. external burner cap (C); 4. internal burner cap (D). Note: make sure that: 1. the locating pin for the burner ring (A) is inserted correctly in the slot on the burner unit. 2. that the locating pin on the external burner cap (C) is inserted in the slot on the burner ring (A).
5019_719_01132_GB 1-06-2007 14:30 Pagina 14 General cleaning & maintenance Always disconnect the hob from the electrical power supply and wait until it cools before cleaning and/or doing maintenance work. n order to keep your hob in good condition, you must keep it clean, removing any remaining food each time you use it. Cleaning the hob surface: • the stainless steel surface may become stained if it comes into contact with hard water over along period of time or with extremely strong cleaning products.
5019_719_01132_GB 1-06-2007 14:30 Pagina 15 Troubleshooting guide If the hob is not working properly, work through this guide before contacting our Customer Care Centre. 3. the end part of the thermocouple is clean. The pans are not stable? Check that: 1. the bottom of the pan is perfectly flat. 2. the pan is centred on the burner. 3. the pan supports are correctly positioned with all the rubber feet in place. The burner does not ignite, or the flame is unsteady? Check that: 1.
5019_719_01132_GB 1-06-2007 14:30 Pagina 16 Whirlpool Europe S.r.l. Viale G. Borghi, 27 - 21025 Comerio (VA) Phone 0332.759111 - Fax 0332.759268 www.whirlpool.