Midline Blender Service Manual MODELS Australian Series 5KSB555AAC (Almond Creme) 5KSB555AER (Empire Red) 5KSB555AGR (Imperial Grey) 5KSB555AOB (Onyx Black) 5KSB555AWH (White) Britain Series 5KSB555BAC (Almond Creme) 5KSB555BER (Empire Red) 5KSB555BMY (Majestic Yellow) 5KSB555BOB (Onyx Black) 5KSB555BWH (White) 5KSB555BBU (Cobalt Blue) 5KSB555BPK (Pink) 5KSB555BNK (Brushed Nickel) 5KSB555BPM (Pearl Metallic) European Series 5KSB555EAC (Almond Creme) 5KSB555EER (Empire Red) 5KSB555EGR (Imperial Grey) 5KSB55
BLENDER SERVICE MANUAL SAFETY GUIDELINES Your safety and the safety of others are very important. We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages. This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others. All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.
BLENDER SERVICE MANUAL BLENDER REPAIR MANUAL SUBJECT PAGE SAFETY GUIDELINES ............................................................................................................................. 2 PRODUCT FEATURES ............................................................................................................................ 4 PREPARING THE BLENDER FOR USE .................................................................................................
BLENDER SERVICE MANUAL Product Features The following are some of the KitchenAid Blender’s unique product features (Fig. 1): 1. 2. 3. 4. 5. 4 Figure 1 Stay-Put Lid with Clear, 60 ml Ingredient Cup: Provides a strong seal. The flexible lid will maintain its tight seal throughout the life of the blender. The lid incorporates a removable 60 ml cup for convenience in measuring and adding ingredients. Easy Pour 1.5 L Glass Pitcher: Glass pitcher resists scratches, stains, and odors.
BLENDER SERVICE MANUAL 5. Adjust the length of the blender power cord (Fig.6). Blender Assembly 1. Put locking collar with blades pointing up on a sturdy surface (Fig. 2). Figure 2 2. Put sealing ring (1), flat side down, around the blades and into the groove within the locking collar (2) (Fig. 3). Figure 6 6. Put pitcher assembly onto the blender base (Fig. 7). 1 2 Figure 3 3. Align the pitcher tabs with the slots of the locking collar (Fig. 4).
BLENDER SERVICE MANUAL Preliminary Inspection of Blender Operating the KitchenAid Blender Before servicing the blender, the following inspection should be performed. All service should be performed on a clean, dry surface with good illumination. The KitchenAid blender will operate in two different operating modes: Continuous mode and pulse mode. • Lid and Ingredient Cap: Place the lid on top of the jar and push securely on the jar with the ingredient cap in place.
BLENDER SERVICE MANUAL Blender Service Procedures WARNING If any of the rubber feet (2) are heavily soiled or cracked, you should replace all four of them. When replacing or installing the rubber feet (2), make sure that they are all inserted equally into the power base (1) so that the blender will sit level on the work surface. Power Cord Replacement (Fig. 10) Always be sure to inspect the condition of the blender’s power cord (4) before running the unit.
BLENDER SERVICE MANUAL Electronic Speed Control Board Replacement (Fig. 11) To replace the electronic speed control board (9), disconnect filter connector (10), motor connector (11), and hall effect connector (12) from the electronic speed control board (9). Motor Replacement (Fig. 13) After the coupler (14) has been removed, disconnect the motor connector (11) and the hall effect connector (12) from the control board (9). Remove the two Phillips screws (16) and motor (17) from the upper housing (5).
BLENDER SERVICE MANUAL Hall Effect Sensor (Fig. 15) The various speeds of the blender are maintained under varying load conditions with a hall effect sensor (20), located at the bottom of the motor (17). To remove the hall effect sensor (20), use a flathead screwdriver to open two tabs (21) that hold the hall effect sensor (20) to the motor (17). Disconnect connector (12) from the control board (9).
BLENDER SERVICE MANUAL Parts List Unit Parts For Variations of Model 5KSB555A Item No. 1 7 1 Part No.
BLENDER SERVICE MANUAL Attachment Parts For Variations of Model 5KSB555A Item No. 1 Part No.
BLENDER SERVICE MANUAL Parts List Unit Parts For Variations of Model 5KSB555B Item No. 1 7 1 Part No.
BLENDER SERVICE MANUAL Attachment Parts For Variations of Model 5KSB555B Item No. 1 Part No.
BLENDER SERVICE MANUAL Parts List Unit Parts For Variations of Model 5KSB555E Item No. 1 7 1 Part No.
BLENDER SERVICE MANUAL Attachment Parts For Variations of Model 5KSB555E Item No. 1 Part No.
BLENDER SERVICE MANUAL Parts List Unit Parts For Variations of Model 5KSB555S Item No. 1 7 1 Part No.
BLENDER SERVICE MANUAL Attachment Parts For Variations of Model 5KSB555S Item No. 1 Part No.
FOR THE WAY IT’S MADE. TM KitchenAid Countertop Appliances St. Joseph, Michigan 49085 U.S.A. ® Registered Trademark/TM Trademark of Kitchen Aid, U.S.A. Printed in U.S.A.