Owner's Manual

12
MICROWAVE OVEN CARE
General Cleaning
IMPORTANT: Before cleaning, make sure all controls are off and
the microwave oven is cool. Always follow label instructions on
cleaning products.
Soap, water, and a soft cloth or sponge are suggested rst, unless
otherwise noted.
STAINLESS STEEL (on some models)
NOTE: To avoid damage to stainless steel surfaces, do not use
soap-lled scouring pads, abrasive cleaners, cooktop polishing
creme, steel-wool pads, gritty washcloths, or abrasive paper
towels. Damage may occur to stainless steel surfaces, even with
one-time or limited use.
Rub in direction of grain to avoid damaging.
Cleaning Method:
■ Affresh
®
Stainless Steel Cleaners (not included): See the
“Accessories” section.
■ Vinegar for hard water spots
MICROWAVE OVEN DOOR EXTERIOR
Cleaning Method:
■ Glass cleaner and a soft cloth or sponge:
Apply glass cleaner to soft cloth or sponge, not directly on
panel.
MICROWAVE OVEN CAVITY
To avoid damage to microwave oven cavity, do not use soap-
lled scouring pads, abrasive cleaners, steel-wool pads, gritty
washcloths, or some paper towels.
On stainless steel models, rub in direction of grain
to avoid damaging.
The area where the microwave oven door and frame touch when
closed should be kept clean.
Cleaning Method:
Average soil
■ Mild, nonabrasive soaps and detergents:
Rinse with clean water and dry with soft, lint-free cloth.
Heavy soil
■ Mild, nonabrasive soaps and detergents:
Heat 1 cup (250 mL) of water for 2 to 5 minutes in microwave
oven. Steam will soften soil. Rinse with clean water and dry
with soft, lint-free cloth.
Odors
■ Lemon juice or vinegar:
Heat 1 cup (250 mL) of water with 1 tbs (15 mL) of either lemon
juice or vinegar for 2 to 5 minutes in microwave oven.
TURNTABLE
Replace turntable immediately after cleaning. Do not operate the
microwave oven without the turntable in place.
Cleaning Method:
■ Mild soap and water
■ Dishwasher
TURNTABLE SUPPORT AND ROLLERS, HUB
■ Mild soap and water or dishwasher
NONSTICK CAVITY COATING (on some models)
To avoid damage to the microwave oven cavity, do not use metal
or sharp utensils or scrapers or any type of abrasive cleanser or
scrubbers.
Replacing The Cavity Light
Cavity Light is located at the top front of the microwave oven,
under the cover and is replaceable.
To replace the cavity light refer the following steps.
1. Use a Phillips head screwdriver to remove the 4 wood screws
securing the trim kit frame to the cabinet.
2. Using 2 people, slide the microwave oven out of the cabinet.
Unplug the microwave oven and place on a stable surface with
the microwave door and frame sitting slightly beyond the edge
of the surface.
3. Remove the 3 short screws to release the leftside cooling duct,
see below pictorial. Set screws and cooling duct aside.
A. Trim kit frame
B. Mounting hole guide
C. #7-16x15/16" at head wood screw (4)
D. Cutout ceiling
WARNING
Excessive Weight Hazard
Use two or more people to move and install
air conditioner.
Failure to do so can result in back or other injury.
A. Cabinet
B. Microwave Oven
A
B
A. Leftside Cooling Duct
B. Short Screws (3)
C. Screw holes (3)
MICROWAVE OVEN CARE
4. Remove the 4 screws which fasten the trim kit frame to the
microwave oven, and set the 4 screws aside.
5. Pull the Trim Kit Frame away from the front of the microwave
to release it. Note the ‘TOP’ and ‘up arrow’ molded into the
frame, the 4 locating pins and the locating slots, set frame
aside.
6. Remove the light cover screw from the top front of the
microwave oven.
7. Remove the light cover.
8. Disengage hook to remove LED board.
9. Unplug the LED terminal.
10. Connect replacement LED to terminal and snap it into place,
securing with the hook.
11. Plug in the LED terminal removed in step 9.
12. Reattach the LED board removed in step 8.
13. Reattach the Light cover removed in step 7.
14. Reattach the light cover screw removed in step 6.
15. Reattach the trim kit frame that was removed in step 5, to the
microwave oven by rst aligning the 4 locating slots with the
locating pins.
16. Use the 4 screws removed in step 4, to fasten the trim kit
frame to the microwave oven.
17. Use the 3 screws removed in step 3 to reattach the leftside
cooling duct.
18. Slide the microwave oven back to the cabinet. Plug in the
microwave oven.
19. Reattach the trim kit frame and microwave to the cabinet
using the screws removed in step 1.
A
B
C
A. Trim Kit Frame
B. #7-18x7/16" round head sheet metal screw (4)
C. Screw holes (4)
A
B
C
A. Trim Kit Frame
B. Locating pin (4)
C. Locating slot (4)
Screw
Light cover
Top front of the
microwave oven
Hooks
Terminal
Hook
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
WARNING
B
A
C