Owner's Manual
Table Of Contents
- MICROWAVE OVEN SAFETY
- Microwave Oven Safety
- MICROWAVE OVEN MAINTENANCE AND CARE
- General Cleaning
- INSTALLATION INSTRUCTIONS
- REQUIREMENTS
- Tools and Parts
- Location Requirements
- Product Dimensions
- Installation Dimensions
- Electrical Requirements
- INSTALLATION
- Prepare Microwave Oven Hood Combination
- Installation Types
- Find the Cardboard Plate
- Find the Wall Stud(s)
- Find the Flush Point
- Mark Upper Cabinet
- Mark Rear Wall
- Drill holes in Upper Cabinet
- Drill holes in Rear Wall
- Attach Mounting Plate to Wall
- Rotate Blower Motor
- Install Damper Assembly
- Install the Microwave Oven
- Complete Installation
- VENTING DESIGN SPECIFICATIONS
- Venting Design Specifications
- SEGURIDAD DEL HORNO MICROONDAS
- Seguridad del horno de microondas
- MANTENIMIENTO Y CUIDADO DEL HORNO MICROONDAS
- Limpieza general
- INSTRUCCIONES DE INSTALACIÓN
- REQUISITOS
- Herramientas y piezas
- Requisitos de Ubicación
- Dimensiones del producto
- Dimensiones de instalación
- Requisitos eléctricos
- INSTALACIÓN
- Preparar la combinación de horno de microondas y campana
- Tipos de instalación
- Encontrar plantilla de cartón
- Encontrar las vigas de pared
- Encontrar el Punto al Ras
- Marcar gabinete superior
- Marque la pared posterior
- Taladrar los orificios en el gabinete superior
- Taladre orificios en la pared posterior
- Fije la placa de montaje a la pared
- Gire el Motor del Soplador
- Instale el Conjunto de la Compuerta
- Instalación del horno de microondas
- Complete la instalación
- ESPECIFICACIONES PARA EL DISEÑO DE LA VENTILACIÓN
- Especificaciones para el Diseño de la Ventilación
4
MICROWAVE OVEN
MAINTENANCE AND CARE
General Cleaning
IMPORTANT: Before cleaning, make sure all controls are off and
the microwave oven is cool. Always follow label instructions on
cleaning products.
Soap, water, and a soft cloth or sponge are suggested first, unless
otherwise noted.
STAINLESS STEEL AND BLACK STAINLESS
STEEL (on some models)
NOTE: To avoid damage to stainless steel surfaces, do not use
soap-filled scouring pads, abrasive cleaners, Cooktop Cleaner,
steel-wool pads, gritty washcloths, or abrasive paper towels.
Damage may occur to stainless steel surfaces, even with one-time
or limited use.
Rub in direction of grain to avoid damaging.
Cleaning Method:
� Affresh
®
✝
Stainless Steel Cleaners Part Number W10355016
(not included) or affresh
®
Stainless Steel Cleaning Wipes Part
Number W1055049 (not included):
See the Quick Start Guide for ordering information.
� Vinegar for hard water spots.
MICROWAVE OVEN DOOR EXTERIOR
Cleaning Method:
� Glass cleaner and a soft cloth or sponge: Apply glass cleaner
to soft cloth or sponge, not directly on panel.
� Affresh
®
Kitchen Appliance Cleaners Part Number
W10355010 (not included): See “Online Ordering Information”
section from Quick Start Guide to order.
NONSTICK CAVITY COATING (on some models)
To avoid damage to the microwave oven cavity, do not use metal
or sharp utensils or scrapers or any type of abrasive cleanser or
scrubbers.
MICROWAVE OVEN CAVITY
To avoid damage to the microwave oven cavity, do not use
soap-filled scouring pads, abrasive cleaners, steel-wool pads,
gritty washcloths, or some paper towels.
On stainless steel models, rub in direction of grain to avoid
damaging.
The area where the microwave oven door and frame touch when
closed should be kept clean.
Cleaning Method:
Average soil
� Mild, nonabrasive soaps and detergents:
Rinse with clean water and dry with soft, lint-free cloth.
Heavy soil
� Mild, nonabrasive soaps and detergents:
Heat 1 cup (250 mL) of water for 2 to 5 minutes in microwave
oven. Steam will soften soil. Rinse with clean water and dry
with soft, lint-free cloth.
Odors
� Lemon juice or vinegar:
Heat 1 cup (250 mL) of water with 1 tbs (15 mL) of either
lemon juice or vinegar for 2 to 5 minutes in microwave oven.
GREASE FILTERS
� Mild cleanser and scouring pad
� Dishwasher
INSTALLATION INSTRUCTIONS
REQUIREMENTS
Tools and Parts
Tools Needed
� Measuring tape
� Pencil
� Scissors
� Masking tape or thumbtacks
� Drill
� No. 2 Phillips screwdriver
� Stud finder
� No. 3 Phillips screwdriver for 1/4 - 20 x 3" (76 mm) bolts
� 3/16" (5 mm), 3/8" (10 mm), 5/8" (16 mm) drill bits
� 3/4" (19 mm) hole saw
� Keyhole saw
� Diagonal wire cutting pliers
� 7/16" (11 mm) socket wrench (or box wrench) for 1/4" x 2"
(6.4 mm x 51 mm) lag screws
� 1
1
/
2
" (38 mm) diameter hole drill bit for wood or metal cabinet
� Caulking gun and weatherproof caulking compound
� Duct tape.
Materials Needed
� Standard fittings for wall or roof venting. See the “Venting
Design Specifications” section.
✝affresh is a registered trademark of Whirlpool, U.S.A.