Owner's Manual
Table Of Contents
- MICROWAVE OVEN SAFETY
- Microwave Oven Safety
- Internet Connectivity Guide for Connected Appliances Only
- FCC Caution
- MICROWAVE OVEN MAINTENANCE AND CARE
- General Cleaning
- INSTALLATION INSTRUCTIONS
- REQUIREMENTS
- Tools and Parts
- Location Requirements
- Product Dimensions
- Installation Dimensions
- Electrical Requirements
- INSTALLATION
- Prepare Microwave Oven Hood Combination
- Installation Types
- Find the Cardboard Plate
- Find the Wall Stud(s)
- Find the Flush Point
- Mark Upper Cabinet
- Mark Rear Wall
- Drill holes in Upper Cabinet
- Drill holes in Rear Wall
- Attach Mounting Plate to Wall
- Rotate Blower Motor
- Install Damper Assembly
- Install the Microwave Oven
- Complete Installation
- VENTING DESIGN SPECIFICATIONS
- SEGURIDAD DEL HORNO MICROONDAS
- Seguridad del Horno Microondas
- Guía de Conectividad a Internet solo para Electrodomésticos Conectados
- Precaución de FCC
- MANTENIMIENTO Y CUIDADO DEL HORNO MICROONDAS
- Limpieza general
- INSTRUCCIONES DE INSTALACION
- REQUISITOS
- Herramientas y piezas
- Requisitos de Ubicación
- Dimensiones del producto
- Dimensiones de Instalación
- Requisitos eléctricos
- INSTALACION
- Prepare la combinación de horno microondas y campana
- Tipos de Instalación
- Encontrar plantilla de cartón
- Encuentre las vigas de pared
- Encontrar el punto al ras
- Marque el gabinete superior
- Marque la pared posterior
- Taladre los orificios en el gabinete superior
- Taladre orificios en la pared posterior
- Fije la placa de montaje a la pared
- Gire el motor del soplador
- Instale el conjunto de la compuerta
- Instalación del horno microondas
- Complete la instalación
- ESPECIFICACIONES PARA EL DISENO DE LA VENTILACION
15
Mark Rear Wall
The microwave oven must be installed on a minimum of 1 wall
stud, preferably 2, using a minimum of 1 lag screw, preferably 2.
See “Find the Wall Stud(s)” section for find the wall studs.
1. Use a pencil to mark the power cord hole and two mounting
nut holes.
A
A. Centerline
2. Align the center markers on the cardboard plate, to the
centerline on the wall, making sure it is level, and that the top
of the cardboard template is butted up against the back edge
of the upper cabinet. (see following NOTE before making
marks).
Use a pencil to mark the wall venting hole (wall venting
installation only), skip it if your unit is for recirculation or upper
cabinet venting installation.
A
B
C
A. Back Edge of Upper Cabinet
B. Wall Venting Hole
C. Cardboard Plate
NOTE:
� If the front edge of the upper cabinet is lower than the back
edge, lower the cardboard template so that its top is level
with the front edge of the cabinet.
A
C
B
D
A. Rear wall
B. Cardboard plate
C. Top of cardboard plate must align with front edge of
cabinet
D. Front edge of upper cabinet
3. Hold the cardboard plate on the rear wall while aligning the
side center marks (B) on the cardboard plate with the vertical
centerline draw in step 1. Make sure the cardboard plate is
level, and that the top of the cardboard template is butted up
against the bottom edge of the upper cabinet.
B
A
C
A. Bottom Edge of Upper Cabinet and Top of the
Cardboard Plate
B. Side Center Marks on Cardboard Plate
C. Centerline
4. Find and mark the two bottom position lines (A) on the
cardboard plate.
A
A. Cardboard Plate Bottom Position Line
5. Using the bottom edge of the cardboard plate, align it with the
two small lines (A), and draw a line (B) indicating where the
bottom edge of the mounting plate (C) should be.
A
B
C
A. Two Small Lines
B. Cardboard Plate Bottom Line
C. Bottom Edge of Mounting Plate