Owner's Manual
Table Of Contents
- BUILT-IN MICROWAVE/OVEN COMBO SAFETY
- Built-In Microwave/Oven Combination Safety
- MICROWAVE OVEN MAINTENANCE AND CARE
- General Cleaning
- Self-Cleaning Cycle
- Steam Clean (on some models)
- INSTALLATION INSTRUCTIONS
- REQUIREMENTS
- Tools and Parts
- Location Requirements
- Electrical Requirements
- INSTALLATIONS
- Prepare Built-In Oven
- Remove Oven Door(s)
- Make Electrical Connection
- Install Oven
- Install Deflector Kit
- Replace Oven Door(s)
- Complete Installation
- SÉCURITÉ DE L’ENSEMBLE FOUR ÉLECTRIQUE/FOUR À MICRO-ONDES ENCASTRÉ
- Sécurité de l’ensemble four électrique/four à micro-ondes encastré
- ENTRETIEN ET RÉPARATION DU FOUR À MICRO-ONDES
- Nettoyage général
- Programme d’autonettoyage
- Steam Clean (nettoyage à la vapeur) (sur certains modèles)
- INSTRUCTIONS D’INSTALLATION
- SPÉCIFICATIONS
- Outils et pièces
- Exigences d’emplacement
- Spécifications électriques
- INSTALLATION
- Préparer le four encastré
- Enlever la/les porte(s) du four
- Raccordement électrique
- Installation du four
- Installation de l’ensemble de déflecteurs
- Réinstallation de la/des porte(s) du four
- Achever l’installation
- SEGURIDAD DE LA COMBINACIÓN DE HORNO MICROONDAS/HORNO INTEGRADO
- Seguridad de la combinación de horno microondas/horno integrado
- MICROWAVE OVEN MAINTENANCE AND CARE
- Limpieza general
- Ciclo de autolimpieza
- Steam Clean (Limpieza con vapor) (en algunos modelos)
- INSTRUCCIONES DE INSTALACIÓN
- REQUISITOS
- Herramientas y piezas
- Requisitos de ubicación
- Requisitos eléctricos
- INSTALACIONES
- Preparación del horno empotrado
- Retire las puertas del horno
- Hacer la conexión eléctrica
- Para instalar el horno
- Instale el kit de deflector
- Vuelva a colocar las puertas del horno
- Finalización de la instalación
14
6. After the bottom vent shield is installed.
� Align the bottom vent trim tab (B) with the oven frame (A)
as shown.
� Using one #8-18 x 3/8" (9.5 mm) screw (C) on each side of
the trim tab (B), align the top edge of the bottom vent trim
tab (E) with the hinge receiver edge (D) as shown.
� Fasten the bottom vent trim securely to the oven frame (A).
D
B
E
A. Oven frame
B. Trim tab
C. #8-18 x 3/8" (9.5 mm)
screw
D. Hinge receiver edge
E. Bottom Vent Trim Tab top
edge
7. Replace the oven racks.
8. Replace the oven door. See the “Replace Oven Door(s)”
section.
9. Check that the door is free to open and close. If it is not,
repeat the removal and installation procedures. See the
“Prepare Built-In Oven” section.
10. Repeat for lower oven door.
IMPORTANT: For proper oven operation, check that the gap
between bottom trim of the door and bottom vent trim is at least
1/4" (6.4 mm).
11. Reconnect power.
12. The display panel will light briefly, and “PF” may appear in the
display.
13. If the display panel does not light, refer the Warranty.
14. If F9E0 error code is encountered upon powering up the unit,
the appliance is wired incorrectly at the Junction Box or
Electrical Panel. Contact a qualified electrician to verify the
home electrical supply and the hardwire connection at the
Junction Box or Electrical Panel (See the Electrical
Connection Options section).
Positioning Oven Feet
The oven feet need to be installed to allow the microwave/oven
combination to be installed in a Flush Installation or in Standard
Installations where the cutout height is 42
1
/
2
" (107.9 cm) or more.
NOTE: Do not remove the spacers.
A. Spacers
1. Using 2 or more people, place the on its back on a covered
surface.
A
C
B