Owner's Manual
Table Of Contents
- BUILT-IN MICROWAVE/OVEN COMBO SAFETY
- Built-In Microwave/Oven Combination Safety
- MICROWAVE OVEN MAINTENANCE AND CARE
- General Cleaning
- Self-Cleaning Cycle
- Steam Clean (on some models)
- INSTALLATION INSTRUCTIONS
- REQUIREMENTS
- Tools and Parts
- Location Requirements
- Electrical Requirements
- INSTALLATIONS
- Prepare Built-In Oven
- Remove Oven Door(s)
- Make Electrical Connection
- Install Oven
- Install Deflector Kit
- Replace Oven Door(s)
- Complete Installation
- SÉCURITÉ DE L’ENSEMBLE FOUR ÉLECTRIQUE/FOUR À MICRO-ONDES ENCASTRÉ
- Sécurité de l’ensemble four électrique/four à micro-ondes encastré
- ENTRETIEN ET RÉPARATION DU FOUR À MICRO-ONDES
- Nettoyage général
- Programme d’autonettoyage
- Steam Clean (nettoyage à la vapeur) (sur certains modèles)
- INSTRUCTIONS D’INSTALLATION
- SPÉCIFICATIONS
- Outils et pièces
- Exigences d’emplacement
- Spécifications électriques
- INSTALLATION
- Préparer le four encastré
- Enlever la/les porte(s) du four
- Raccordement électrique
- Installation du four
- Installation de l’ensemble de déflecteurs
- Réinstallation de la/des porte(s) du four
- Achever l’installation
- SEGURIDAD DE LA COMBINACIÓN DE HORNO MICROONDAS/HORNO INTEGRADO
- Seguridad de la combinación de horno microondas/horno integrado
- MICROWAVE OVEN MAINTENANCE AND CARE
- Limpieza general
- Ciclo de autolimpieza
- Steam Clean (Limpieza con vapor) (en algunos modelos)
- INSTRUCCIONES DE INSTALACIÓN
- REQUISITOS
- Herramientas y piezas
- Requisitos de ubicación
- Requisitos eléctricos
- INSTALACIONES
- Preparación del horno empotrado
- Retire las puertas del horno
- Hacer la conexión eléctrica
- Para instalar el horno
- Instale el kit de deflector
- Vuelva a colocar las puertas del horno
- Finalización de la instalación
16
Install Deflector Kit
1. Install the deflector (B) to the lower vent piece (D) using two
#8-18 x 1/4" (6.4 mm) screws on each side.
NOTE: On 27" (68.6 cm) models, only one #8-18 x 1/4"
(6.4 mm) screw is used on each side.
B
A
C
D
A. #8-18 x 1/4"
(6.4 mm) screws
B. Deflector
C. Upper vent piece
D. Lower vent piece
2. Align vent tab (B) with oven frame (A) as shown in the
following illustration.
3. Using one #8-18 x 3/8" (9.5 mm) screw (E) on each side of the
vent tab (B), fasten the vent securely to the oven.
E
D
C
B
A
A. Oven frame
B. Vent tab
C. Oven vent
D. Deflector
E. #8-18 x 3/8" (9.5 mm) screw
Replace Oven Door(s)
1. Using two hands, grasp side edges of door at the midpoint.
Face the oven cavity.
2. Locate the slots on each side of the oven cavity for the door
hinge locks.
A. Slot in the oven cavity for door hinge lock
3. Using 2 hands, grasp the edges of the oven door. At a 45°
angle, insert the hinges at the same time, and push the oven
door into the oven cavity slot to replace. You may need to
gently shift the door from side to side as you push.
4. Make sure the door hinge notch is engaged on the bottom
of the oven cavity slot.
IMPORTANT: Do not close the door at this step or damage
may occur to the door hinge.
5. Lower the oven door to the fully open position. If the oven door
does not open to a full 90°, repeat steps 1 through 3.