Owner's Manual

ManualsBrandsKitchenAid ManualsMicrowave Wall Oven CombinationsSelf-Cleaning Convection Microwave Wall Oven Combo (Stainless steel) (Common: 30 -in; Actual: 30.0-in)

Table Of Contents

To Steam Clean:

1. Open the oven door of the selected oven and remove all racks

and accessories from the oven cavity.

2. Pour 10 oz (295.7 mL) of distilled or filtered water into the

oven bottom. Then close the oven door.

3. Touch the Tools keypad.

On double-oven models: Select Upper Cavity or Lower Cavity.

4. Select STEAM CLEAN.

5. Select START.

6. After approximately 1 hour, a tone will sound to signal the end

of the cycle. Touch the Oven Cancel keypad for single oven

models and the Upper/Lower keypad for double oven models

to clear the display.

7. When the oven is completely cooled, remove any excess

water with a sponge or cloth and wipe down oven interior. If

needed, use a non-scratch copper scrubbing pad to remove

stubborn soils.

INSTALLATION INSTRUCTIONS

REQUIREMENTS

Tools and Parts

Gather the required tools and parts before starting

installation. Read and follow the instructions provided

with any tools listed here

Tools Needed

� Phillips screwdriver

� Measuring tape

� Hand or electric drill (for wall cabinet installations)

� 1" (2.5 cm) drill bit (for wall cabinet installations)

� Level

� Flat-blade screwdriver

Parts Supplied

� #8-14 x 3/4" (1.9 cm) screws (2)

� #8-18 x

" (9.5 mm) screws - bottom vent shield (2)

� #8-18 x 3/8" (9.5 mm) screws - bottom vent trim (2)

� Rear feet (2)

� Front feet (2)

� Bottom vent and shield

Check local codes. Check existing electrical supply. See the

“Electrical Requirements” section.

It is recommended that all electrical connections be made by a

licensed, qualified electrical installer

NOTE: Be sure to purchase only whirlpool factory-certified parts

and accessories for your appliance. Your installation may require

additional parts. To order, refer to the contact information

referenced in your Quick Start Guide.

Location Requirements

IMPORTANT: Observe all governing codes and ordinances.

� Cabinet opening dimensions that are shown must be used.

Given dimensions provide minimum clearance with oven.

� Recessed installation area must provide complete enclosure

around the recessed portion of the oven.

� Grounded electrical supply is required. See “Electrical

Requirements” section.

� Electrical supply junction box should be located 3" (7.6 cm)

maximum below the support surface when the oven is installed

in a wall cabinet. A 1" (2.5 cm) minimum diameter hole should

have been drilled in the right rear or left rear corner of the

support surface to pass the appliance cable through to the

junction box.

� Oven support surface must be solid, level and flush with bottom

of cabinet cutout. Floor must be able to support a total weight

(microwave and built-in oven) of 208 lbs (95 kg) for 27"

(68.6 cm) models or 249 lbs (113 kg) for 30" (76.2 cm) models.

IMPORTANT: To avoid damage to your cabinets, check with

your builder or cabinet supplier to make sure that the materials

used will not discolor, delaminate or sustain other damage.

This oven has been designed in accordance with the

requirements of UL and CSA International and complies with

the maximum allowable wood cabinet temperatures of

194°F (90°C).

Cabinet Dimensions — Built-in Microwave/Oven

Combination

Standard Installation

27" (68.6 cm) models

A. 27" (68.6 cm) minimum cabinet

width

B. 1

" (3.2 cm) top of cutout to

bottom of upper cabinet door

C. 19

" (48.9 cm) bottom of

cutout to floor is

recommended.

7"-19

" (17.8-48.9 cm) bottom

of cutout to floor is acceptable.

D. 25

" minimum (64.8 cm)

cutout width

E. 1

" (3.8 cm) minimum bottom

of cutout to top of cabinet door

F. 41

" (105 cm)*

recommended cutout height

G. 24" (60.7 cm) cutout depth

30" (76.2 cm) models

A. 30" (76.2 cm) minimum cabinet