Control Guide

10
Convection Roast (on some models)
Convection roasting can be used for roasting meats and poultry.
During convection roasting, the broil, convect, and CleanBake
™
elements (on some models) will cycle on and off in intervals to
maintain oven temperature, while the fan circulates the hot air.
If the oven door is opened during convection roasting, the fan
turns off immediately when the door is opened and turns on
immediately when the door is closed. Bake, broil, and convect
elements will turn off approximately 30 seconds after the door is
opened. They will turn on again approximately 30 seconds after
the door is closed.
NOTE: it is normal for the convection fan to run during non-
convection cycles as well as during preheat.
To Convection Roast
Before convection roasting, position racks according to the “Rack
and Bakeware Positions” section. It is not necessary to wait for the
oven to preheat before putting food in, unless recommended in
the recipe.
Convection Broil (on some models)
During convection broiling, the broil element will cycle on and off
in intervals to maintain oven temperature, while the fan circulates
the hot air.
The temperature is preset at 550°F (288°C), but can be changed
to a different temperature. Cooking times will vary depending on
the rack position and temperature and may need to be adjusted.
If the oven door is opened during convection broiling, fan turns off
immediately when the door is opened and turns on again
immediately when the door is closed. Broil elements will turn off
approximately 30 seconds after the door is opened. They will turn
on again approximately 30 seconds after the door is closed.
NOTE: It is normal for the convection fan to run during
non-convection cycles as well as during preheat.
To Convection Broil:
Allow the oven to preheat for 5 minutes. Position food on the
unheated grid on the broiler pan, and then place it in the center of
the oven rack with the longest side parallel to the door.
Proofing Bread
Proofing bread prepares dough for baking by activating the yeast.
Proofing twice is recommended unless the recipe directs
otherwise.
To Proof
Before first proofing, place dough in a lightly greased bowl and
cover loosely with waxed paper or plastic wrap coated with
shortening. Place on rack guide 2. See “Rack and Bakeware
Positions” for diagram. Close door.
1. Touch Upper or Lower Proof. Display will show 100°F
(38°C).
2. Touch Start.
Let dough rise until nearly doubled in size, and then check at
20 to 25 minutes. Proofing time may vary depending on dough
type and quantity.
3. Touch Cancel for the selected oven when finished proofing.
Before second proofing, shape dough, place in baking pan(s) and
cover loosely. Follow same placement, and control steps above.
Before baking, remove waxed paper or plastic wrap.
Temperature Probe (single, upper,
and on some models, lower oven)
The temperature probe accurately measures the internal
temperature of meat, poultry and casseroles with liquid and
should be used in determining the doneness of meat and poultry.
The temperature probe should only be used with Bake, Convect
Bake or Convect Roast.
Always unplug and remove the temperature probe from the oven
when removing food.
To Use
Before using, insert the probe into the food item. (For meats, the
probe tip should be located in the center of the thickest part of the
meat and not into the fat or touching a bone). Place food in oven
and connect the temperature probe to the jack. Keep probe as far
away from heat source as possible. Close oven door.
NOTE: The temperature probe must be inserted into the food item
before the mode is selected.
1. Touch the number keys to enter a probe temperature. The
probe temperature is the desired internal temperature of the
food when it is done. The temperature can be set between
110°F and 200°F (43°C and 93°C).
2. Touch Upper or Lower Bake, Convect Bake or
Convect Roast.
3. Touch Start.
The set oven temperature will appear on the oven display
throughout cooking.
“Lo°” will appear as the probe temperature until the internal
temperature of the food reaches 45°F (7°C). Then the display
will show the temperature increasing.
When the set probe temperature is reached, the oven will shut
off automatically and “Cooking Complete” will appear on the
oven display.
4. Touch Cancel for the selected oven, or open the oven door to
clear the display and/or stop reminder tones.
5. Always unplug and remove the temperature probe from the
oven when removing food. The probe symbol will remain lit in
the display until the probe is unplugged.
To Change Probe Temperature During a Cooking Cycle
1. Touch a probe enabled cooking mode (Bake, Convect Bake,
or Convect Roast).
2. Follow steps 1 through 5 in the “To Use” section.