Owner's Manual
Table Of Contents
- BUILT-IN OVEN SAFETY
- Built-In Oven Safety_WOBIMW_OM_W11340821A
- OVEN MAINTENANCE AND CARE
- General Cleaning
- Self-Cleaning Cycle
- Steam Clean (on some models)
- INSTALLATION INSTRUCTIONS
- REQUIREMENTS
- Tools and Parts
- Location Requirements
- Electrical Requirements
- INSTALLATIONS
- Prepare Built-In Oven
- Remove Oven Door(s)
- Positioning Oven Feet for Multiple Cabinet Cutout Heights
- Make Electrical Connection
- Install Oven
- Replace Oven Door(s)
- Complete Installation
- SECURITE DU FOUR ENCASTRE
- Sécurité du four encastré
- ENTRETIEN ET REPARATION DU FOUR
- Nettoyage général
- Programme d’autonettoyage
- Steam Clean (nettoyage à la vapeur) (sur certains modèles)
- INSTRUCTIONS D'INSTALLATION
- SPECIFICATIONS
- Outils et pièces
- Exigences d’emplacement
- Spécifications électriques
- INSTALLATIONS
- Préparer le four encastré
- Enlever la/les porte(s) du four
- Positionner les pieds du four pour des ouvertures de découpe dans l’armoire
- Raccordement électrique
- Installation du four
- Réinstallation de la/des porte(s) du four
- Achever l’installation
- Blank Page
- Blank Page
- Blank Page
- Blank Page
- Blank Page
- Blank Page
- Blank Page
8
Cabinet Dimensions - Double Ovens, Standard
Installation
Double Ovens Installed in Cabinet
27" (68.6 cm) models
A. 27" (68.6 cm) minimum
cabinet width
B. 1
1
/
4
" (3.2 cm) top of cutout to
bottom of upper cabinet door
C. 14
3
/
4
" (37.5 cm) bottom of
cutout to floor is
recommended.
4"-14
3
/
4
" (10.2 cm - 37.5 cm)
bottom of cutout to floor is
acceptable.
D. 25
1
/
2
" (64.8 cm) minimum
cutout width
E. 1
1
/
2
" (3.8 cm) minimum
bottom of cutout to top of
cabinet door
F. 50
1
/
4
" (127.6 cm)*
recommended cutout height
G. 24" (60.7 cm) cutout depth
30" (76.2 cm) models
A. 30" (76.2 cm) minimum
cabinet width
B. 1
1
/
4
" (3.2 cm) top of cutout to
bottom of upper cabinet door
C. 14
3
/
4
" (37.5 cm) bottom of
cutout to floor is
recommended.
4"-14
3
/
4
" (10.2 cm - 37.5 cm)
bottom of cutout to floor is
acceptable.
D. 28
1
/
2
" (72.4 cm) minimum
cutout width
E. 1
1
/
2
" (3.8 cm) minimum
bottom of cutout to top of
cabinet door
F. 50
1
/
4
" (127.6 cm)*
recommended cutout height
G. 24" (60.7 cm) cutout depth
*
NOTE: The cutout height can be between 48
7
/
8
" and 52
3
/
16
"
(124.1 cm and 132.6 cm) for double ovens.
NOTE: Contact service to get tall shield for cutouts greater than
28
11
/
16
" (72.9 cm) to enhance installation.
Cabinet Dimensions - Single Ovens, Flush
Installations
NOTE: This is an alternate option to install your product in the
cabinet and obtain a flush look. For standard installation, refer
section "Cabinet Dimensions - Single Ovens, Standard
Installation".
A 25" (63.5 cm) minimum cutout depth is required.
These dimensions will result in a 1/4" (6 mm) reveal on the top, a
1/4" (6 mm) reveal on the sides, and a 1/8" (3 mm) reveal on the
bottom of the wall oven.
The front face of the cleats and platform will be visible and should
be treated as a finished surface.
Single Ovens Installed in Cabinet
Front View
27" (68.6 cm) Models
A. 3/4" (1.9 cm) top cleat*
B. 27
1
/
4
" (69.2 cm) minimum width
of flush inset cutout
C. 25
7
/
8
" (65.7 cm) minimum width
of opening
D. 29
1
/
4
" (74.3 cm) minimum
height of flush inset cutout
E. 28
1
/
2
" (72.4 cm) recommended
cutout height
F. 11/16" (1.7 cm) side cleat*
G. 1/4"x 2" (6.4 mm x 5.1 cm)
spacer the entire depth of the
cutout*
H. Recommended junction box
location
I. 4
5
/
8
"- 32" (11.7 - 81.3 cm)
bottom of cutout to floor
J. 25" (63.5 cm) minimum depth
of cutout
Side View
30" (76.2 cm) Models
A. 3/4" (1.9 cm) top cleat*
B. 30
1
/
4
" (76.8 cm) minimum width
of flush inset cutout
C. 28
7
/
8
" (73.3 cm) minimum width
of opening
D. 29
1
/
4
" (74.3 cm) minimum
height of flush inset cutout
E. 28
1
/
2
" (72.4 cm) recommended
cutout height
F. 11/16" (1.7 cm) side cleat*
G. 1/4" x 2" (6.4 mm x 5.1 cm)
spacer the entire depth of the
cutout*
H. Recommended junction box
location
I. 4
5
/
8
" - 32" (11.7 - 81.3 cm)
bottom of cutout to floor
J. 25" (63.5 cm) minimum depth
of cutout
* Cleats and spacers must be recessed 1
3
/
8
" (3.5 cm) from the
front of the cabinet.