Stand Mixer - Bowl Lift W11378207C.
PARTS AND FEATURES 1 2 4 RESET OFF/0 STIR 2 4 6 8 10 7 3 6 18 8 5 19 9 12 10 11 13 14 16 15 17 1 Motor Head 11 Bowl* 2 Attachment Hub 12 Bowl Handle* 3 Attachment Knob 13 Flex Edge Beater** 4 Hinged Hub Cover 14 Flat Beater** 5 Beater Shaft 15 Spiral Dough Hook** 6 Speed Control 16 Wire Whip** 7 Bowl Lift Lever 17 8 Beater Height Adjustment Screw 11-Wire Stainless Steel Elliptical Whip** 9 Bowl Support 18 Pouring Shield** 10 Locating Pins 19 Spring Latch
ENGLISH PRODUCT SAFETY IMPORTANT SAFEGUARDS When using electrical appliances, basic safety precautions should always be followed, including the following: 1. Read all instructions. 2. To protect against the risk of electrical shock do not put Stand Mixer in water or other liquid. 3.
PRODUCT SAFETY ELECTRICAL REQUIREMENTS WARNING Voltage: 120 V Frequency: 60 Hz NOTE: The power rating for your Stand Mixer is printed on the serial plate. Electrical Shock Hazard Plug into a grounded 3 prong outlet. Do not remove ground prong. Do not use an extension cord. If the power supply cord is too short, have a qualified electrician or service person install an outlet near the appliance. The maximum rating is based on the attachment that draws the greatest load (power).
ENGLISH SPEED CONTROL GUIDE All speeds features Soft Start® which allows the Stand Mixer to start at a lower speed to help avoid ingredient splash-out and “flour puff” at start-up, then increases to the selected speed. The speed control can be set between the speeds listed in the chart to obtain speeds 1, 3, 5, 7, and 9 if a finer adjustment is required.
PRODUCT ASSEMBLY 1 2 Spring latch RESET OFF/0 STIR 2 4 6 8 10 Locating pin Turn the Stand Mixer to “OFF/ 0” and then unplug. To attach the bowl: Fit the bowl supports over locating pins and press down on back of the bowl until bowl pin snaps into spring latch. IMPORTANT: If the bowl is not securely snapped into place, it will be unstable and wobble during use. 3 4 Pin To attach the accessory: Slip the accessory onto the shaft. Turn to hook it over the pin on the shaft.
ENGLISH PRODUCT ASSEMBLY WARNING Electrical Shock Hazard Plug into a grounded 3 prong outlet. Do not remove ground prong. Do not use an adapter. Do not use an extension cord. Failure to follow these instructions can result in death, fire, or electrical shock. 5 6 Raise Bowl Test the beater to bowl clearance: Plug the Stand Mixer into a grounded 3 prong outlet. Turn Stand Mixer ON and test each speed, making sure the beater does not touch the bowl during operation.
PRODUCT ASSEMBLY USING THE POURING SHIELD* Use the pouring shield to avoid having ingredients splashing out of the bowl when mixing, as well as to easily pour ingredients into the bowl while mixing. 1 2 To attach the pouring shield*: Slide the pouring shield from the front of the Stand Mixer over the bowl. The bottom rim of the pouring shield* fits inside of the bowl. Pour the ingredients into the bowl through the pouring chute. *Available with select models only and available as an accessory purchase.
ENGLISH PRODUCT USAGE WARNING WARNING Injury Hazard Unplug mixer before touching beaters. Failure to do so can result in broken bones, cuts, or bruises. Electrical Shock Hazard Plug into a grounded 3 prong outlet. Do not remove ground prong. Do not use an adapter. Do not use an extension cord. Failure to follow these instructions can result in death, fire, or electrical shock. 1 2 RESET OFF/0 STIR 2 4 6 8 10 Plug the Stand Mixer into a grounded 3 prong outlet.
PRODUCT USAGE OPTIONAL ATTACHMENTS KitchenAid® offers a wide range of optional attachments such as the Spiralizer, Pasta Cutters, or Food Grinder that may be attached to the Stand Mixer attachment power hub. 1 2 RESET OFF/0 STIR 2 4 6 8 10 Turn the Stand Mixer to “OFF/ 0” and then unplug. Flip up hinge attachment hub cover to open. 3 4 Insert attachment into attachment hub, making certain that attachment power shaft fits into the square attachment hub socket.
ENGLISH PRODUCT DISASSEMBLY 2 1 RESET OFF/0 STIR 2 4 6 8 10 Turn the Stand Mixer to “OFF/ 0” and then unplug. Remove Pouring shield: Lift the front of the pouring shield* clear of the rim of the bowl. Pull away from the Stand Mixer. 3 4 Remove the accessory: Press accessory upward and turn to the left. Pull down the accessory from beater shaft. To Remove Bowl: Place bowl-lift lever in the down position. Grasp bowl handle and lift straight up and off locating pins 11 W11378207C.
CARE AND CLEANING IMPORTANT: Do not immerse the Stand Mixer body in water or other liquids. 2 1 RESET OFF/0 STIR 2 4 6 8 10 Turn the Stand Mixer to “OFF/ 0” and then unplug. Wipe the Stand Mixer body with a soft, damp cloth. 3 4 The following parts are dishwasher-safe, top rack only: Bowl, Flat beater, Flex edge beater*, Spiral dough hook, 11 wire elliptical whip* and Pouring shield*. The following part should be hand-washed only, using warm, soapy water and drying thoroughly: Wire whip only.
ENGLISH TROUBLESHOOTING GUIDE WARNING Electrical Shock Hazard Plug into a grounded 3 prong outlet. Do not remove ground prong. Do not use an adapter. Do not use an extension cord. Failure to follow these instructions can result in death, fire, or electrical shock. Problem Solution Under heavy loads with extended mixing time periods, you If Stand Mixer warms up during may not be able to comfortably touch the top of the Stand use: Mixer. This is normal. If Stand Mixer emits a pungent This is normal.
WARRANTY AND SERVICE KITCHENAID ® STAND MIXER WARRANTY FOR THE 50 UNITED STATES, THE DISTRICT OF COLUMBIA, PUERTO RICO, AND CANADA This warranty extends to the purchaser and any succeeding owner for Stand Mixers operated in the 50 United States, the District of Columbia, Puerto Rico, and Canada. Length of Warranty: One Year Full Warranty from date of purchase. KitchenAid Will Pay for Your Choice of: Hassle-Free Replacement of your Stand Mixer.
ENGLISH WARRANTY AND SERVICE HASSLE-FREE REPLACEMENT WARRANTY—50 UNITED STATES, DISTRICT OF COLUMBIA, AND PUERTO RICO We’re so confident the quality of our products meets the exacting standards of KitchenAid that, if your Stand Mixer should fail within the first year of ownership, KitchenAid will arrange to deliver an identical or comparable replacement to your door free of charge and arrange to have your original Stand Mixer returned to us.
DISCOVER MORE. DÉCOUVREZ PLUS. DESCUBRA MÁS. KITCHENAID.COM/QUICKSTART PRODUCT QUESTIONS OR RETURNS QUESTIONS SUR LE PRODUIT OU LES RETOURS PREGUNTAS SOBRE EL PRODUCTO O DEVOLUCIÓNES USA: 1.800.541.6390 | KitchenAid.com CANADA: 1.800.807.6777 | KitchenAid.ca MEXICO: KitchenAid.com.mx LATIN AMERICA: KitchenAid-Latam.com ®/™ ©2019 KitchenAid. All rights reserved. KITCHENAID and the design of the stand mixer are trademarks in the U.S. and elsewhere. Used under license in Canada. Tous droits réservés.