Owner's Manual
Table Of Contents
- REFRIGERATOR SAFETY
- Refrigerator Safety
- REFRIGERATOR CARE
- Cleaning
- Changing the LED Module
- Refrigerator Shelves
- Opening and Closing Doors
- Vacation and Moving Care
- INSTALLATION INSTRUCTIONS
- Unpack the Refrigerator
- Location Requirements
- Electrical Requirements
- Water Supply Requirements
- Connect the Water Supply
- Complete the Installation
- Install Air Filter (on some models)
- Install Produce Preserver (on some models)
- REFRIGERATOR FEATURES
- Crisper Humidity Control (on some models)
- Water and Ice Dispensers (on some models)
- Ice Maker and Storage Bin
- Water Filtration System
- DOOR AND HANDLE INSTRUCTIONS
- Door and Drawers
- Remove and Replace Handles
- Remove Refrigerator Doors and Hinges
- Reset Bottom Refrigerator Door Hinge
- Replace Refrigerator Doors and Hinges
- Remove and Replace Refrigerator Drawer
- Door Closing and Alignment
- PERFORMANCE DATA SHEET
- Performance Data Sheet
- SÉCURITÉ DU RÉFRIGÉRATEUR
- Sécurité du réfrigérateur
- ENTRETIEN DU RÉFRIGÉRATEUR
- Nettoyage
- Remplacer le module à DEL
- Tablettes du réfrigérateur
- Ouverture et fermeture des portes
- Précautions à prendre avant les vacances ou le déménagement
- INSTRUCTIONS D’INSTALLATION
- Déballage du réfrigérateur
- Exigences d’emplacement
- Spécifications électriques
- Spécifications de l’alimentation en eau
- Raccordement à la canalisation d’eau
- Terminer l’installation
- Installer le filtre à air (sur certains modèles)
- Installation du conservateur de produits frais (sur certains modèles)
- CARACTÉRISTIQUES DU RÉFRIGÉRATEUR
- Commande d’humidité dans le bac à légumes (sur certains modèles)
- Distributeur d’eau et de glaçons (sur certains modèles)
- Machine à glaçons et bac d’entreposage
- Système de filtration de l’eau
- INSTRUCTIONS POUR LA PORTE ET LA POIGNÉE
- Porte et tiroirs
- Pour enlever et réinstaller les poignées
- Démontage des portes et charnières du réfrigérateur
- Réinitialiser la charnière inférieure du réfrigérateur
- Réinstallation des portes et charnières
- Retrait et réinstallation du tiroir de congélation
- Fermeture et alignement des portes
- FICHE DE DONNÉES DE PERFORMANCE
- Fiche de données de performance
24
3. Reconnect Wiring (if applicable)
� Align the two ends of the wiring connector and push them
together until you hear a click sound and feel the tabs snap
into place on the connector.
� Gently pull on the wiring connection to ensure the wiring
connection is completely seated. Replace the wiring cover.
NOTE: The wiring connection must be complete for the
drawer temperature control to operate.
4. Replace the drawer bins onto the drawer glides.
Remove and Replace Freezer Drawer Front
Depending on the width of your door opening, it may be necessary
to remove the freezer drawer front to move the refrigerator into
your home.
IMPORTANT:
� If the refrigerator was previously installed and you are moving
it out of the home, before you begin, turn the refrigerator
control Off, and unplug the refrigerator or disconnect power.
Remove food and any adjustable door or utility bins from
doors.
� Two people may be required to remove and replace the
freezer drawer
Tools Needed: 1/4" hex driver
REMOVE DRAWER
Front Style 1 & 2
1. Open the freezer drawer to its full extension.
2. Loosen the two screws at the top, inside the drawer front (one
on the left-hand side and one on the right-hand side) that
fasten the drawer front to the drawer glides as shown below.
3. Remove the 2 screws at the bottom, inside the drawer front
that fasten the drawer front to the drawer glides as shown
below.
4. Lift up on the drawer front to release the plastic studs from the
drawer glide bracket slots as shown below.
Style 1 Style 2
A. Drawer glide bracket slots A. Drawer glide bracket slots
5. Slide the drawer glides back into the freezer.
Front Style 3
1. Open the freezer drawer to full extension.
2. Loosen the four screws attaching the drawer glides to the
drawer front as shown below.
NOTE: Loosen screws three to four turns. Keep the screws in
the drawer front.
A. Four Bracket screws
3. Lift drawer front upward and off the screws.
REPLACE DRAWER
Front Style 1 and 2
1. Pull out the freezer drawer glides to their full extension.
2. Holding the drawer front by its sides, align the two plastic
studs, located at the bottom, inside the drawer front, with the
drawer glide bracket slots.
NOTE: It helps if one person holds the drawer glides steady
while another person aligns the drawer front and inserts the
studs into the slots.
Style 1 Style 2
A. Drawer front screw A. Drawer front screw
B. Drawer front plastic stud
3. Replace and tighten the two screws at the top of the drawer
front (one on the left-hand side and one on the right-hand
side).