Owner's Manual

4
To store vegetables:
Set the control to VEG to store vegetables at their optimal storage
temperatures.
NOTE: If food starts to freeze, move the control to the right (less
cold), toward the VEG setting. Remember to wait 24 hours between
adjustments.
Crisper Humidity Control
You can control the amount of humidity in the moisture-sealed crisper.
Adjust the control to any setting between LOW and HIGH.
LOW (open) for best storage of fruits and vegetables with skins.
HIGH (closed) for best storage of fresh, leafy vegetables.
Water and Ice Dispensers
NOTES:
■ Connect to potable water supply only.
■ The dispensing system will not operate when freezer door is open.
■ Allow 24 hours for the refrigerator to cool down and chill water.
■ Allow 24 hours to produce the rst batch of ice. Discard the
rst three batches of ice produced. Wait 72 hours for full ice
production.
Flush the Water System
Air in the water dispensing system can cause the water dispenser to
drip. After connecting the refrigerator to a water source or replacing
the water lter, ush the water system. Flushing the water dispensing
system forces air from the water line and lter, and prepares the water
lter for use.
NOTE: As air is cleared from the system, water may spurt out of the
dispenser.
1. Using a sturdy container, depress and hold the water dispenser
pad for 5 seconds, then release it for 5 seconds.
2. Repeat Step 1 until water begins to ow.
3. Once water begins to ow, continue depressing and releasing the
dispenser pad (5 seconds on, 5 seconds off) until a total of 3 gal.
(12 L) has been dispensed.
Additional ushing may be required in some households.
Calibrate Measured Fill
Household water pressure may affect the accuracy of the Measured
Fill feature. For optimum performance of your water dispenser, you
must rst calibrate Measured Fill.
IMPORTANT: Flush the water system before calibrating Measured Fill.
1. Place a sturdy measuring cup (1 cup [237 mL] size) on the
dispenser tray, centered in front of the water dispenser pad.
NOTE: Depending on your model, a measuring cup may be
provided.
2. Press and hold the OPTIONS and LOCK buttons at the same time
for 3 seconds. The words “Back” and “1 Cup” will appear on the
display screen.
3. Using your hand (not the measuring cup), press and release the
water dispenser pad in order to dispense water to the 1 cup ll
line.
NOTE: If overlling or spilling occurs, discard the water and press
“Back” to restart the calibration process.
4. When 1 cup of water has been correctly dispensed into the
measuring cup, press the MEASURED FILL button under the word
“Conrm” to conrm the calibration.
When Measured Fill calibration has been conrmed, the display will
return to the home screen.
The Water Dispenser
IMPORTANT:
■ Dispense at least 1 qt (1 L) of water every week to maintain a fresh
supply.
■ If the ow of water from the dispenser decreases, it could be
caused by low water pressure.
■ With the water lter removed, dispense 1 cup (237 mL) of
water. If 1 cup of water is dispensed in 8 seconds or less,
the water pressure to the refrigerator meets the minimum
requirement.
■ If it takes longer than 8 seconds to dispense 1 cup of
water, the water pressure to the refrigerator is lower than
recommended. See “Water Supply Requirements” (in the
User Instructions or the Installation Instructions and Owner’s
Manual) or “Problem Solver” for suggestions.
To Dispense Water (Standard):
1. Press a sturdy glass against the water dispenser pad. Hold the
glass close to the water dispenser spout to ensure that the water
dispenses into the glass.
NOTE: While dispensing water and for 3 seconds after dispensing
has stopped, the digital display will show how much water has
been dispensed.
2. Remove the glass to stop dispensing.
To Dispense Water (Measured Fill):
Measured Fill allows you to dispense a specied amount of water with
the touch of a few buttons.
NOTE: The amount of water you select will be dispensed. Be sure
that the container is empty and can hold the entire volume. If ice is in
the container, you may need to adjust your selection.
IMPORTANT: Low water pressure may affect the accuracy of this
feature.
1. Press MEASURED FILL to turn the feature on. When the feature is
on, the Measured Fill screen appears on the display.
Press ICE MODE to manually turn off the Measured Fill feature.
NOTE: The dispenser will automatically turn off Measured Fill
after 1 minute of inactivity. When Measured Fill is turned off,
any changes you have made will be lost and all defaults will be
restored.
Calibrate Measured Fill
ICE AND WATER