Owners Manual
Table Of Contents
- REFRIGERATOR SAFETY
- Refrigerator Safety
- MAINTENANCE AND CARE
- Cleaning
- Lights
- Freezer Shelf (number varies by model)
- Vacation and Moving Care
- INSTALLATION INSTRUCTIONS
- Unpack the Refrigerator
- Location Requirements
- Electrical Requirements
- Water Supply Requirements
- Connect Water Supply
- Complete the Installation
- Install Air Filter (on some models)
- Install Produce Preserver (on some models)
- REFRIGERATOR FEATURES
- Convertible Drawer Temperature Control (on some models)
- Crisper Humidity Control (on some models)
- Dual Evaporator (on some models)
- Water and Ice Dispensers
- Ice Maker and Storage Bin
- Water Filtration System
- DOOR REMOVAL AND LEVELING STYLE 1
- Door Instructions
- Install and Remove Door Handles
- Remove Doors and Hinges
- Replace Doors and Hinges
- Door Closing and Alignment
- DOOR REMOVAL AND LEVELING STYLE 2
- Door Instructions
- Install and Remove Door Handles
- Remove Doors and Hinges
- Door Closing, Leveling, and Alignment
- PERFORMANCE DATA SHEET
- Performance Data Sheet
- SÉCURITÉ DU RÉFRIGÉRATEUR
- Sécurité du réfrigérateur
- ENTRETIEN ET RÉPARATION
- Nettoyage
- Lampes
- Tablettes du congélateur (le nombre varie selon le modèle)
- Précautions à prendre avant les vacances ou le déménagement
- INSTRUCTIONS D’INSTALLATION
- Déballage du réfrigérateur
- Exigences d’emplacement
- Spécifications électriques
- Spécifications de l’alimentation en eau
- Raccordement à la canalisation d’eau
- Terminer l’installation
- Installer le filtre à air (sur certains modèles)
- Installation du conservateur de produits frais (sur certains modèles)
- CARACTÉRISTIQUES DU RÉFRIGÉRATEUR
- Commande de température dans le tiroir convertible (sur certains modèles)
- Commande d’humidité dans le bac à légumes (sur certains modèles)
- Évaporateur double (sur certains modèles)
- Distributeurs d’eau et de glaçons
- Machine à glaçons et bac d’entreposage
- Système de filtration de l’eau
- RETRAIT DE LA PORTE ET AJUSTEMENT DU NIVEAU, STYLE 1
- Instructions pour la porte
- Installation et retrait des poignées de la porte
- Démontage des portes et charnières
- Réinstallation des portes et charnières
- Fermeture et alignement des portes
- RETRAIT DE LA PORTE ET AJUSTEMENT DU NIVEAU, STYLE 2
- Instructions pour la porte
- Installation et retrait des poignées de la porte
- Démontage des portes et charnières
- Fermeture, mise à niveau et alignement des portes
- FICHE DE DONNÉES DE PERFORMANCE
- Fiche de données de performance
22
10. Check and make sure that the technician sheet is placed in
the base grille cavity before assembling the base grille into the
cabinet.
11. Reinstall the base grille into the cabinet, introducing the left
side first and then the right side of the base grille as shown
below. You may accommodate the water dispenser tubing and
wiring into base grille cavity below the left bottom hinge.
12. Attach the base grille by pushing it into the cabinet clips.
Door Leveling
The refrigerator doors are designed to be slightly misaligned
vertically when the refrigerator is empty. If the doors are uneven
after food has been placed, please follow the next instructions:
1. Use an 11/16" open-ended wrench to loosen the locking nut
located below the refrigerator door as shown below.
Accommodate the wrench so that it fits in the space.
2. Use a 5/16" open-ended wrench tool to turn the alignment
screw as shown below. Depending on how the refrigerator
door is misaligned in relation to the freezer door, you must turn
the screw to the right to raise or to the left to lower the
refrigerator door until both doors have been aligned vertically.
3. Tighten the 11/16" locking nut with the wrench.
4. Attach the base grille if it was dislodged.
Door Alignment
1. Locate the hinges on top of your refrigerator. Loosen the hinge
screws two full turns.
2. Place the provided alignment tool between the doors so that
the block sits on top of the doors.
3. Tighten the left and right hinge screws on the refrigerator top.
4. Remove the alignment tool. If the gap between doors is
uniform, store the tool for future adjustments.
5. If the gap is not uniform, repeat the alignment procedure with
medium (M) or high (H) gap widths of the tool facing down
until a uniform gap is achieved.