APPLIANCES 8546448 528138/8546448
Table of Contents Drawer lnstaBtation instructions Dishwasher Safety ............................ 2 lnstaIBation Requirements ............................. Tools and Parts ................................... Location Requirements 3 3 ............................. Water Supply Requirements 3 ......................... 4 Electrical Requirements ............................. 4 .............................. 5 Prepare Cabinet Opening ........................... Ebctrical Connection ..............
INSTALLATIONREQUIREMENTS Gather the required tools and parts before instalhtion, Read and follow the instructions any tools listed here, starting provided Tools needed: [] 7 mm socket wrench [] utility knife [] 5 mm socket wrench [] [] [] needle-nose pliers tape measure flat-bladed screwdriver [] [] [] [] pencil [] [] sandpaper level [] wood cutting board [] adjustable wrench that opens to 1-1/8" (29 mm) with IMPORTANT: Observe all governing codes and ordinances.
Cabinet dimensions/requirements For dishwasher: moisture protection tape [] Not water line with 4.3-145 psi (30-1000 kPa) water pressure. [] 120°F (48.8°C) water at dishwasher. [] An easily accessible valve with 3/8" compression fitting must be installed in the hot water supply line. 4 ,_ (10cm) 32-5/16 "- 34-5/8" (82_0 cm - 88_0 cm) Utility hole: C-.'.' C.' 1-1/2"(3_8crn)din. hole, eitherside immediately J adjacent Emectrical Shock Hazard tocorner. \ _ \\\\\\\ Plug into a grounded Do not rem
Garbage Disposer: Ifyouplantoinstalla garbage disposer, anadditional separate 120-volt, 60Hz,AC-only, 15or20ampfusedebctrical supplyis required. Recommended groundmethod Thisappliance mustbegrounded. Thisappliance isequipped withapowersupply cordhaving 3 prongground plug.To minimize possible shockhazard, thecordmustbeplugged intoa mating prongground-type outlet,grounded inaccordance with localcodesandordinances.
4, Asthedishwasher isbeingpushed intotheopening, slowly pulltheinlethose,drainhoses andpowersupplycord through theutilityhole. 5, Remove thestrapfromupperdrawer. Goto"IfInstalling Flexible TrimPieces" section. 6, Rotate drawer to the right onto its side and place on the protective cover. Option2: DirectWiringMethod (-\ "J I electrical cover 7, Slide the left-hand runner back into the dishwasher. 8, The electrical cover is located in the back Ieft corner.
6. Remove thehouse wiringknockout, knockout ElectricalShockHazard Connect 7, Runthehouse wiringthrough theconduit connector (not supplied) andintothedishwasher through theknockout opening, Failure ground wire to green to do so can result ground in death screw. or electrical shock. 11. Piace the ground wire under the green ground screw, Use a 7 mm socket wrench to securely tighten the green ground screw, 12. Tighten the conduit connector, Replace electrical cover, 13.
17,Usethesidecuttingplierstocutthecabletiesecuring the hoses andpowersupplycordtothebackofthedishwasher. back of dishwasher 22, As the dishwasher is being pushed into the opening, slowly pull the inlet hose and drain hoses through the utility hole. Let the house wiring gather behind the dishwasher. 23, Remove the strap from upper drawer. ::, cable tie 18, Completely remove the power supply cord and save it, in case a power cord installation is needed in the future.
6, Rotate the drawer to the right onto its side and place on the protective cover. Choose attachment option Option 1: Side attachment 1. The dishwasher side attaching tabs are accessed through holes in the sound insulation. IMPORTANT: For best installation, use all four attaching tabs. / 2. Secure the attaching tabs to the cabinet using #8 Phillips head screws. side i 7, Slide the left-hand runner back into the dishwasher. 8.
Option 1, 2: Top attachment If the top attaching brackets are used, open the top drawer slightly: 2, Option 2: Garbage disposaB connection 1, Screw the top attaching brackets to the underside counter with two #8 Phillips head screws. IMPORTANT: a maximum The top attaching brackets 3/4" (19 mm) vertical gap. of the 2, Route the drain hoses as shown and press the hoses into the drain hose support, Decide if the drain hoses need to be trimmed, trim can accommodate 3, .......
5. Attachthedrainhoseconnector totheairbreakusing thesuppliedhoseclamp, EJ_ air break E drain hose connector waste 1. Remove material. front panels 2. On the shorter front panel tape securing the connector 3. Connect the end connector from from of the the box and discard (lower drawer), remove the and wires. Discard tape. medallion lower all shipping connector to the drawer. wire opening water supply lower front panel 8" (20.3 cm) min.
Option1:Insta{Istandardtoe pane{ NOTI=S: Depending oncountertop height, youmaynothaveto trimthetoepanel. Rugs placedinfrontofdishwasher couldinterfere with toepanel. Clearance between floorandtoepanelmay needtoinclude therugthickness. 1. Partially openthebottom drawer. 2. Turnthetoepanelupside downandholdvertically against the bottomedgeofthetubside(notthefront). 3. Onthetoepanel, markwherethetub'sbottomedgeis. 7, Remove any rough 8, Partially open bottom drawer.
Option 2: Install custom front panels Custom front 1. Prepare 2. Mount the not extend panem dimensions the custom is customer 9 == 2-5/16" (5_9cm) Lay the custom covering. 4. Measure and position line panels to specifications to the custom panel.The the back surface of the supplied, 3. I"_-- (22.9 cm) front handle beyond front mark location panel is customer face down the vertical on the back front preference.) on a protective centedine of the shown. screws must panel.
10,LaythemetaH pilateonthebackofthecustomfront panel 11,AHign thecenterHine marked onthecustompaneH withthe diamondshapeandnotchinthemetaH pilateto centerthe metaH pilatehodzontaHHy, AHign thehodzontaH Hine withthe topofthemetaH pilate, 15, Line up the bracket holies with the pin holies and repHace each pin so that the pin Hine is vertical horizontal line / [ top of plate centerline 16, Repeat steps 2-15 for other custom Option 2: _nsta{I custom panel toe pane_ Oustom toe pane_ dimensions 12, Us
6. Ifneeded, youmaysimplypushthetoepanelbackorforward onthemounting rail. 7. WithaPhillips screwdriver, tighten thetoepanelclamping screws onbothsides. toe panel mounting rail clamping screw i \ \ 8. Plug in dishwasher or reconnect power. 1. Check to be sure all parts are now installed. If there is an extra part, go back through the steps to see which step was skipped. 2. Check to be sure you have all of your tools. 3. Dispose of/recycle all packaging materials. 4.
Part No. 8546448 © 2004 KitchenAid ® Registered KitchenAid trademark/TM trademark of KitchenAid, Canada Hcensee in Canada U.S.A., Printed Benton Harbor, Michigan 49022 in U.S.A.
