Installation guide
Install
Custom
Panel
-
Option
2
(Models
KUDCOSIV
and
KUDS30IV)
All
models
require
an
accessory
option
to
attach
custom
panels.
Kit
Number
8171555
(black),
8171556
(white)
or
8171557
(biscuit)
are
available.
To
order,
call
customer
service
at
1-800-444-1230.
NOTE:
A
custom
full-front
panel
must
weigh
no
more
than
14
lbs
(6.3 kg)
and
must
be
made
to
specific
dimensions.
It
is
recommended
that
a
cabinetmaker
cut
the
custom
panel
because
of
the
precise
dimensions
needed.
IMPORTANT:
Use
a
moisture-resistant
sealer
on
both
sides
and
all
edges
of
the
panel
to
avoid
damage
from
humidity.
NOTE:
These
dimensions
are
for
frameless
custom
panel
models
with
a
4"
(10.2
cm)
console
only.
Custom
panel
installation
-
Dishwashers
with
control
panel
on
the
front
23%"
Tsu
"
(65.8
(65.8
cm)
se"
(65.8
cm)
eo
My
Rito.
mm)
*
This
dimension
is
for
4"
(10.2
cm)
toe
kick.
If
the
installation
needs
a
higher
toe
kick,
adjust
the
height
of
the
wood
panel
accordingly.
Not
recommended
for
toe kicks
greater
than
6"
(15.2
cm).
J
With
a
TORX®
screwdriver,
remove
three
screws
from
both
sides,
as
shown;
hold
the
outer panel
up
while
removing
the
screws.
Save
screws
for
reinstallation.
Custom
panel
dimensions—
Dishwashers
with
control
panel
on
the
front
3
screws
per
side
outer
panel
Jo
Gently
set
outer
panel
aside.
Lay
the
cutomer-supplied
custom
panel
face
down
on
a
non-scratching
surface.
Position
the
outer
panel
on the
back
of
the
customer-supplied
custom
panel
as
shown;
make
sure
top
edge
of
the
outer
panel
is
aligned
with
the
top
edge
of
the
customer-supplied
custom
panel,
and
both
panels
are
centered
side
to
side.
Mark
pilot
holes
Mark
all
four
hole
locations;
remove
outer
panel
and
drill
%o0"
pilot
holes
44"
(13
mm)
deep,
in
customer-supplied
custom
panel.
Place
the
outer panel
on
the
back
of
the
customer-supplied
custom
panel
and
align
holes.
Attach
outer panel
to
back
of
customer-supplied
custom
panel
with four
#10
x
%"
wood
screws
(not
supplied).
If
the
customer-supplied
custom
panel
is
less
than
34"
(1.9
cm)
thick
where
the
screws
are
attached,
shorter
screws
may
be
required.
4
|
Attach
body
panel
SS
G
Go
aN
Align
top
Reinstall
SS
@
edges
3
screws
each
side
Customer-supplied
panel
Attach
the
panel
assembly
to
the
door
by
reinstalling
the
three
screws
on
each
side.
Choose
Attachment
Option
AWARNING
Excessive
Weight
Hazard
Use
two
or
more
people
to
move
and
install
dishwasher.
Failure
to
do
so
can
result
in
back
or
other
injury.
Using
2
or
more
people,
stand
the
dishwasher
up.
7