Instruction Sheet

ManualsBrandsKitchenAid ManualsAppliances18 in. 50 lb. Built-In Ice Maker in PrintShield Stainless Steel

Table Of Contents

IICCEE MMAAKKEERR DDOOOORR RREEVVEERRSSAALL IINNSSTTRRUUCCTTIIOONNSS

REVERSE DOOR SWING: SIDE SWING ONLY

Tools Needed

Gather the required tools and parts before starting installation.

� 5/16ʺ wrench

� 1/4ʺ wrench

� Flat putty knife

� Phillips screwdriver

Hinge pin 5/16ʺ hex-head hinge screw

Handle screw End cap screw

Remove Stainless Steel Door Wrap

Panel (on some models)

A. Hex-head screws

1. Remove two hex-head

screws (A)

Remove the two hex-head screws

located under the stainless steel door

wrap panel flange on the bottom of the

door.

2. Pull up and outward on door

wrap

Pull up and outward on the door wrap

panel from the bottom.

3. Rotate door wrap panel

Rotate the door wrap panel until it

separates from the door and pull up.

NOTE: Be sure the edge guards do not

separate from the door wrap panel.

Door Stop and End Cap Reversal

WARNING

Electrical Shock Hazard

Disconnect power before servicing.

Replace all parts and panels before operating.

Failure to do so can result in death or electrical shock.

1. Disconnect power to ice maker

Unplug ice maker or disconnect power.

2. Remove handle (on some models)

Remove the handle screws and handle (on some models).

3. Remove hinge pin

Remove the hinge pin (A) from the top hinge.

4. Remove door from hinges

Remove the door from the hinges and replace the top hinge pin

(A).

A. Hinge pin

5. Remove screw and door stop: (A) and (C)

Remove the screw and door stop at corner A. Remove the screw

and end cap at corner C. Place the door stop at corner C, and

tighten screw. Place the end cap at corner A, and tighten screw.

6. Remove screw and door stop: (B) and (D)

Remove the screw and door stop at corner D. Remove the screw

and end cap at corner B. Place the door stop at corner B, and

tighten screw. Place the end cap at corner D, and tighten screw.

A. Top corner open (no end cap)

B. Beginning top corner end cap

C. Beginning bottom corner end cap

D. Bottom corner open (no end cap)

7. Set door aside

Summary of content (8 pages)

PAGE 1
ICE MAKER DOOR REVERSAL INSTRUCTIONS REVERSE DOOR SWING: SIDE SWING ONLY 2. Remove handle (on some models) Tools Needed Gather the required tools and parts before starting installation. � 5/16ʺ wrench � Flat putty knife � 1/4ʺ wrench � Phillips screwdriver Hinge pin 5/16ʺ hex-head hinge screw Handle screw End cap screw Remove Stainless Steel Door Wrap Panel (on some models) Remove the handle screws and handle (on some models). 3. Remove hinge pin Remove the hinge pin (A) from the top hinge. 4.
PAGE 2
Reverse Hinges Replace Door Wrap (on some models) 1. Remove top hinge 1. Place the door wrap flange onto the door top and ensure that it fits correctly. 2. Rotate the door wrap downward until it covers the door surface completely. 3. Install the two hex-head screws into the bottom of the door. Unscrew and remove the top hinge. Replace the screws in the empty hinge holes. Top Hinge Reverse Door Catch 1.
PAGE 3
INSTRUCTIONS D’INVERSION DE LA PORTE DE LA MACHINE À GLAÇONS INVERSION DU SENS D’OUVERTURE DE LA PORTE : PORTE À OUVERTURE LATÉRALE SEULEMENT Outils nécessaires Rassembler les outils et pièces nécessaires avant d’entreprendre l’installation.
PAGE 4
5. Retirer la vis et la butée de porte : (A) et (C) 2. Retirer la charnière inférieure Retirer la vis et la butée de porte à l’angle A. Retirer la vis et la protection d’angle de l’angle C. Placer la butée de porte à l’angle C et serrer la vis. Placer la protection d’angle à l’angle A et serrer la vis. Dévisser et enlever les vis de la charnière inférieure et la charnière. Réinstaller les vis dans les trous vides de la charnière. Charnière inférieure 6.
PAGE 5
Inversion du sens d’installation de la gâche de porte AVERTISSEMENT 1. Ôter les vis inférieures Ôter les vis blanches décoratives du côté opposé de la porte et les mettre de côté. 2.Retirer les vis de poignée de porte Ôter les vis du loquet de porte magnétique et installer le loquet de porte et les vis du côté opposé de la porte. 3. Installer les vis blanches du côté opposé Installer les vis blanches décoratives sur le côté opposé de la porte.
PAGE 6
INSTRUCCIONES PARA INVERTIR EL SENTIDO DE LA PUERTA DE LA FÁBRICA DE HIELO CÓMO INVERTIR EL SENTIDO DE LA PUERTA: SOLO LADO DE APERTURA Herramientas necesarias Reúna las herramientas y las piezas necesarias antes de comenzar la instalación.
PAGE 7
5. Quite el tornillo y el tope de la puerta:(A) y (C) 2. Quite la bisagra inferior Retire el tornillo y el tope de la puerta en la esquina A. Retire el tornillo y la tapa del extremo en la esquina C. Coloque el tope de la puerta en la esquina C y ajuste los tornillos. Coloque la tapa del extremo en la esquina A y apriete los tornillos. Desatornille y quite los tornillos y la bisagra inferior. Vuelva a colocar los tornillos en los orificios vacíos de la bisagra. Bisagra inferior 6.
PAGE 8
Cómo invertir el seguro de la puerta ADVERTENCIA 1. Quite los tornillos blancos Quite los tornillos decorativos blancos del lado opuesto de la puerta y déjelos a un lado. 2. Quite los tornillos del seguro de la puerta Retire los tornillos del seguro magnético de la puerta y colóquelos en el lado opuesto de la puerta. Peligro de choque eléctrico Conecte a un tomacorriente con conexión a tierra de 3 terminales. 3.