4~. &ilkIn Refrigerator \nstajjer: Leave Installation \nstp.pc$ons with the Homeowner. Homeowner: Keep Insta\latiOn jnstmctions for future reference. Save Installation Instructions for local electrical inspector’s use.
Parts supplied installati.on: Before you start... Proper install&ion is your responsibility. Make sure you have everything necessary for correct installation. It is the responsibility of the installer to comply with the installation specifications provided. l The built-in refrigerator weighs over 600 pounds. The floor must be sturdy enough to support this weight ‘plus the additional weight of door panels, food and ice.
Dimensions for built-in area Personal Injury/Property Damage Hazard l Unit is top-heavy and may tip forward when the doors are opened. l A solid soffit or 2” wood block is required above the refrigerator to prevent tipping during use. l If solid soffit is more than 1 inch above refrigerator, a wood block must be installed on the wall noi more than l/4 inch above the refrigerator cover. Failure to follow these instructions could result in personal injury or property damage.
Product dimensions I- Levelers extended 118” below rollers 24 718” - -See page 6. I- i -See page 6.; -1 Height dimensions when the minimum extension of levelers /;‘u”,~:“,“,;;~?2:‘b’:,“’ l L- 23 718” 4 lop ol housing lo lop of grille 118” min. - with 7-112” grille 1-li8” max. -with 8-W” grille 82-112” ret’ es5led heil ghl the weight the rollers: lrom 83.5/8” height with 8-112” grille’ v 83-118” height with 8” grille v’ 82.
Custom door panels, handle inserts and top grille panels Refrigerator Door and top grille panels: Dimensions shown are with routed edges. Routing is required if panels are more than l/4” thick. Freezer - Panel routlng and lop grille door panel 26-114” -, for door panels. I + 114” max. r t door panels 5/16”mln. A4- 3-l/4” min.
Side panel requirements +I- IW tolerance 5132” -+I 23-118” depth protruding door installation > < <=- 23-718” depth flush door inslallaflon 118” spacer thickness * <’ <’ I I I df,sA sid Side trim Refrigerator when 25” depth is available. If less than 25” depth is available, go to step 3. spacers L” ” 1 1. Attach three spacers from the miscellaneous parts bag to the top, middle and bottom of each side of the refrigerator. Spacers are required for ventilation.
Electrical requirements Water supply requirements Use only l/4” copper tubing for water line. l l Electrical Shock Hazard improper connectlon of the equipment-grounding conductor can result In a risk of electrical shock. Check with a qualified electrician or service technician if you are in doubt as to whether the appliance is properly grounded. Do Not use an extensfon cord with this appliance. Such use may result in a fire, electrical shock, or other personal injury.
Product support ::2ip block(s) A solid soffit or a wood block is required to prevent the refrigerator from tipping forward after it is installed. Block(s) must extend to fully cover wldfh of cover. Determine what height the refrigerator will be when it is installed to fit opening. Determine the height to the top of the cover at the final installed height you plan to use. l l l important: Block(s) must extend al least 2” over cover.
14.1 Move refrigerator to kitchen. Place cardboard or plywood under refrigerator. Remove appliance dolly. Open doors and remove all boxes, parts packages and packing materials from inside refrigerator and freezer compartments. Set aside until needed during installation. Do Not remove any protective film until refrigerator is completely installed. Now start... Remove top grille assembly . package, literature package and parts bag taped to the refrigerator door and save.
3-prong grounding wail recepl retainer Remove tape from Move refrigerator close to final position. Remove cardboard or plywood from under refrigerator. Plug electrical cord into the grounded outlet. Use the screw from the parts package to install the plug retainer. Move the refrigerator evenly and straight into the opening. Check that the water line will not be kinked. Check that slack in the electrical cord hangs freely behind refrigerator or is placed on top of refrigerator next to cover.
Check that the power switch is in the “ON” position. Attach top grille decorative panel assembly to the keyhole bracket on the frame and pull down to secure. if the top grille decorative panel does not tit evenly within frame, the keyhole bracket can be moved side to side by adjusting the bracket screws or the decorative panel bracket can be moved up or down by adjusting the decorator panel bracket nuts. 114 Check the water connections at the bottom of the refrigerator again for leaking.
-. If built-in refrigerator does not operate... Check that the circuit breaker is not tripped or house fuse blown. Check that power supply cord is plugged into wall receptacle. A more detailed troubleshooting checklist is provided in the Use and Care Guide. Part No. 2000493 Rev. A 0 1992 KitchenAid If you need assistance... How to arrange for service...
