30" (76.2 CM) AND 36" (91.4 CM) RANGE HOOD Installation Instructions and Use & Care Guide For questions about features, operation/performance, parts, accessories or service, call: 1-800-253-1301 or visit our website at www.whirlpool.com In Canada, call 1-800-807-6777 or visit our website at www.whirlpool.
TABLE OF CONTENTS TABLE DES MATIÈRES RANGE HOOD SAFETY .................................................................2 INSTALLATION REQUIREMENTS ................................................4 Tools and Parts ............................................................................4 Location Requirements ................................................................4 Venting Requirements..................................................................5 Electrical Requirements ..................
IMPORTANT SAFETY INSTRUCTIONS WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: ■ Use this unit only in the manner intended by the manufacturer. If you have questions, contact the manufacturer. ■ Before servicing or cleaning the unit, switch power off at service panel and lock the service disconnecting means to prevent power from being switched on accidentally.
INSTALLATION REQUIREMENTS Tools and Parts Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed here. Tools needed ■ Drill ■ 1¹⁄₄" (3.0 cm) drill bit ■ ¹⁄₈" (3.
Installation Clearances Electrical Requirements C B D A Observe all governing codes and ordinances. Ensure that the electrical installation is adequate and in conformance with National Electrical Code, ANSI/NFPA 70 (latest edition), or CSA Standards C22.1-94, Canadian Electrical Code, Part 1 and C22.2 No. 0-M91 (latest edition) and all local codes and ordinances. If codes permit and a separate ground wire is used, it is recommended that a qualified electrician determine that the ground path is adequate.
INSTALLATION INSTRUCTIONS Prepare Location NOTE: Before making cutouts, make sure there is proper clearance within the ceiling or wall. 1. Disconnect power. 2. Select a flat surface for assembling the range hood. Place covering over that surface. 3. Lift the range hood and set it upside down onto covered surface. 4. If cabinet has recessed bottom, add wood filler strips on each side. Install screws to attach filler strips in locations shown. To wire through top: 1.
Install Range Hood 1. Lift the range hood up under cabinet and determine final location by centering beneath cabinet. Mark on the underside of cabinet the location of the 4 keyhole mounting slots on the range hood. Set range hood aside on a covered surface. A Power Supply Cable Installation 1. For direct wire installations, run the home power supply cable according to the National Electric Code or CSA standards and local codes and ordinances.
Make Electrical Connection WARNING Electrical Shock Hazard Disconnect power before servicing. Replace all parts and panels before operating. Failure to do so can result in death or electrical shock. 1. Disconnect power. G C E D Complete Installation 1. Install the 75W (max.) Incandescent light bulb. See “Replacing the Incandescent Light Bulb” in the “Range Hood Care” section. 2. Replace grease filter if removed. See the “Range Hood Care” section. 3. Check the operation of the range hood fan and light.
RANGE HOOD CARE Cleaning IMPORTANT: Clean the hood and grease filters frequently according to the following instructions. Replace grease filter before operating hood. Exterior Surfaces: IMPORTANT: Do not use soap-filled scouring pads, abrasive cleaners, Cooktop Polishing Creme, steel wool, gritty washcloths or paper towels. To avoid damage to the stainless steel, do not use cleaners that contain chlorine. Cleaning Method: ■ Rub in direction of grain to avoid scratching or damaging the surface.
WIRING DIAGRAM Light Switch On - Off Motor Switch Low - Off - High SE113B R BR BK BK BK BK W R Speed 1 Speed 2 Common BK Ground Screw C10 N 10 W Motor Characteristics Power Supply 120 VAC Frequency 60 Hz 0.35 ±10% A Amperage Wattage Rating 21 ±10% Watts Motor Resistance 46.9 ±10% Ohms White - Red 37.
ASSISTANCE OR SERVICE When calling for assistance or service, please know the purchase date and the complete model and serial number of your appliance. This information will help us to better respond to your request. If you need replacement parts If you need to order replacement parts, we recommend that you use only factory specified parts. Factory specified parts will fit right and work right because they are made with the same precision used to build every new appliance.
WHIRLPOOL CORPORATION MAJOR APPLIANCE WARRANTY LIMITED WARRANTY For one year from the date of purchase, when this major appliance is operated and maintained according to instructions attached to or furnished with the product, Whirlpool Corporation or Whirlpool Canada LP (hereafter “Whirlpool”) will pay for Factory Specified Parts and repair labor to correct defects in materials or workmanship. Service must be provided by a Whirlpool designated service company.
SÉCURITÉ DE LA HOTTE DE CUISINIÈRE Votre sécurité et celle des autres est très importante. Nous donnons de nombreux messages de sécurité importants dans ce manuel et sur votre appareil ménager. Assurez-vous de toujours lire tous les messages de sécurité et de vous y conformer. Voici le symbole d’alerte de sécurité. Ce symbole d’alerte de sécurité vous signale les dangers potentiels de décès et de blessures graves à vous et à d’autres.
IMPORTANTES INSTRUCTIONS DE SÉCURITÉ AVERTISSEMENT : POUR RÉDUIRE LE RISQUE D'INCENDIE, CHOC ÉLECTRIQUE OU DOMMAGES CORPORELS, RESPECTER LES INSTRUCTIONS SUIVANTES : ■ Utiliser cet appareil uniquement dans les applications envisagées par le fabricant. Pour toute question, contacter le fabricant.
EXIGENCES D'INSTALLATION Outils et pièces Exigences d'emplacement Rassembler les outils et pièces nécessaires avant d’entreprendre l’installation. Lire et observer les instructions fournies avec chacun des outils de la liste ci-dessous. IMPORTANT : Observer les dispositions de tous les codes et règlements en vigueur. ■ C’est à l’installateur qu’incombe la responsabilité de respecter les distances de séparation exigées, spécifiées sur la plaque signalétique de l’appareil.
Distances de dégagement à respecter C B D A Spécifications électriques Observer les dispositions de tous les codes et règlements en vigueur. Vérifier que l'installation électrique a été correctement effectuée et qu'elle est conforme aux spécifications de la plus récente édition des normes National Electrical Code, ANSI/NFPA 70, ou de la norme CSA C22.1-94, Code canadien de l'électricité, partie 1 et C22.2 N° 0-M91 (dernière édition) et de tous les codes et règlements en vigueur locaux.
INSTRUCTIONS D’INSTALLATION Préparation de l'emplacement REMARQUE : Avant d’exécuter les découpages, vérifier la disponibilité d’un dégagement suffisant dans le plafond ou le mur pour le conduit d’évacuation. 1. Déconnecter la source de courant électrique. 2. Sélectionner une surface plane pour l’assemblage de la hotte. Placer le matériau de protection sur cette surface. 3. Soulever la hotte et la placer à l'envers sur une surface couverte. 4.
3. Installer les 4 vis de montage 4,5 x 13 mm dans les avanttrous. Laisser un espace d’environ ¹⁄₄" (6,4 mm) entre les têtes des vis et le placard pour faire glisser la hotte et la mettre en place. ¹⁄₄" (6,4 mm) Installation sans décharge à l’extérieur (recyclage) - Ne pas retirer les opercules. 4. À l'aide d'au moins deux personnes, soulever la hotte et la placer à son emplacement final.
AVERTISSEMENT Risque d'incendie Relier le ventilateur à la terre. Utiliser du fil en cuivre. UTILISATION DE LA HOTTE La hotte de cuisinière est conçue pour extraire fumée, vapeurs de cuisson et odeurs de la zone de la table de cuisson.
ENTRETIEN DE LA HOTTE Nettoyage IMPORTANT : Nettoyer fréquemment la hotte et les filtres à graisse en suivant les instructions suivantes. Réinstaller le filtre à graisse avant de faire fonctionner la hotte. Surfaces externes : IMPORTANT : Ne pas utiliser de tampons de récurage savonneux, de nettoyants abrasifs, de crème à polir pour table de cuisson, de laine d’acier, de chiffons de lavage rugueux ou d’essuie-tout.
SCHÉMA DE CÂBLAGE Contacteur du moteur Faible - Arrêt - Élevé Commutateur d'éclairage Marche - Arrêt SE113B MAR N N R N 120 VCA Fréquence Intensité Puissance nominale 60 Hz 0,35 ±10% A 21 ±10% Watts N Vitesse 1 Commun N BL R BL Caractéristiques du moteur Alimentation électrique BL Vitesse 2 MAR BL R BL Vis de mise à la terre Résistance du moteur Blanc - Rouge 46,9 ±10% Ohms Blanc - Noir 37,2 ±10% Ohms C10 NEU L Terre 21
ASSISTANCE OU SERVICE Lors d’un appel pour assistance ou service, veuillez connaître la date d’achat, le numéro de modèle et le numéro de série complets de l’appareil. Ces renseignements nous aideront à mieux répondre à votre demande. Si vous avez besoin de pièces de rechange Si vous avez besoin de commander des pièces de rechange, nous vous recommandons d’employer uniquement les pièces spécifiées par l’usine.
GARANTIE DES GROS APPAREILS MÉNAGERS WHIRLPOOL CORPORATION GARANTIE LIMITÉE Pendant un an à compter de la date d'achat, lorsque ce gros appareil ménager est utilisé et entretenu conformément aux instructions jointes à ou fournies avec le produit, Whirlpool Corporation ou Whirlpool Canada LP (ci-après désignées “Whirlpool”) paiera pour les pièces spécifiées par l'usine et la main-d'œuvre pour corriger les vices de matériaux ou de fabrication.
W10400319B © 2011. All rights reserved. Tous droits réservés. 5/11 Printed in Mexico. Imprimé au Mexique.