KLARK TEKNIK DN32-DANTE Audinate Dante Expansion Module with up to 32 Bidirectional Channels Quick Start Guide
KLARK TEKNIK DN32-DANTE Important Safety Instructions Terminals marked with this symbol carry electrical current of sufficient magnitude to constitute risk of electric shock. Use only high-quality professional speaker cables with ¼" TS or twist-locking plugs pre-installed. All other installation or modification should be performed only by qualified personnel.
4 KLARK TEKNIK DN32-DANTE 10. Coloque el cable de suministro de energía de manera que no pueda ser pisado y que esté protegido de objetos afilados. Asegúrese de que el cable de suministro de energía esté protegido, especialmente en la zona de la clavija y en el punto donde sale del aparato. 11. Use únicamente los dispositivos o accesorios especificados por el fabricante. 12.
6 KLARK TEKNIK DN32-DANTE 18. N’installez pas l’appareil dans un espace confiné tel qu’une bibliothèque ou meuble similaire. 19. Ne placez jamais d’objets enflammés, tels que des bougies allumées, sur l’appareil. 20. Gardez à l’esprit l’impact environnemental lorsque vous mettez des piles au rebus. Les piles usées doivent être déposées dans un point de collecte adapté. 21. Utilisez l’appareil dans un climat tropical et/ou modéré.
8 KLARK TEKNIK DN32-DANTE Instruções de Segurança Importantes Aviso! Terminais marcados com o símbolo carregam corrente elétrica de magnitude suficiente para constituir um risco de choque elétrico. Use apenas cabos de alto-falantes de alta qualidade com plugues TS de ¼" ou plugues com trava de torção pré-instalados. Todas as outras instalações e modificações devem ser efetuadas por pessoas qualificadas.
10 KLARK TEKNIK DN32-DANTE 注意 1. 取扱説明書を通してご覧 ください。 2. 取扱説明書を大切に保 管してください。 3. 警告に従ってください。 4. 指示に従ってください。 5. 本機を水の近くで使用し ないでください。 6. お手入れの際は常に乾燥 した布巾を使ってください。 7. 本機は、取扱説明書の 指示に従い、適切な換気を妨 げない場所に設置してくださ い。取扱説明書に従って設置 してください。 8. 本機は、電気ヒーターや 温風機器、ストーブ、調理台 やアンプといった熱源から離 して設置してください。 9.
12 KLARK TEKNIK DN32-DANTE Warning Failure to observe the following warnings may lead to fatality or serious injury from fire or electric shock. Before installing the card, you must refer to the owner’s manual of the host device or to klarkteknik.com to verify that your host device supports this card, and to verify the number of cards that can be installed in combination with other MIDAS or third-party cards. • • Do not attempt to disassemble or modify the card.
14 KLARK TEKNIK DN32-DANTE 3. Requirements Minimum hardware: Windows-based application - Core 2 Duo CPU, 2 GHz - Ethernet port - 1 GB RAM Mac - 1.5 GHz CPU - Ethernet port - 512 MB RAM Quick Start Guide Recommended Operating Systems: Windows: Windows Windows 7 32-bit or 64-bit, Windows 8 32-bit or 64-bit Mac: 10.6.8 Snow Leopard, 10.7.5 Lion, 10.8 Mountain Lion Dante Controller application provided free of charge at audinate.com. Dante Virtual Soundcard application optional at audinate.com. 5.
16 KLARK TEKNIK DN32-DANTE Quick Start Guide 5.2 M32 with DN32-DANTE straight connection to PC / Mac and Dante Virtual Soundcard 5.4 X32 with DN32-DANTE connection to Midas PRO2 via DN9650 + CM1 Dante card DVS2 , for recording/playback up to 32 x 32 channels 2 for advice on using and licensing Dante Virtual Soundcard visit audinate.com MIDAS Console MIDAS M32 MIDAS M32 with DN32-DANTE Cat 5/6 AES50 @ 96 kHz 24 x 24 channels Laptop Cat 5/6 Ethernet @ 48 kHz Dante 32 x 32 channels 5.
18 KLARK TEKNIK DN32-DANTE Quick Start Guide 5.5 Two M32 consoles with DN32-DANTE connection to DVS for recording 64 simultaneous tracks • Both consoles need to have DN32-DANTE cards installed. • Connect one of the DN32-DANTE Ethernet ports on console A with the card installed in console B. • Connect the second port of console B, either directly with the DAW-PC/Mac or via a network router to which the DAW has access. This link will carry all 64 channels to and from both consoles.
20 KLARK TEKNIK DN32-DANTE • The ROUTING/card out page selects channel blocks that will be provided to the Dante network controller. (e.g. 8 Local Outputs and 3 x 8 signals from AES50 Port A) Quick Start Guide See the M32 line, which is configured for Clock Status Master in the following example: Note that the check boxes for ‘Slave to External Word Clock’ are unchecked in this application. Alternative Synchronisation: Use the internal clock as master clock.
22 KLARK TEKNIK DN32-DANTE Quick Start Guide The Dante Controller must now be configured for “Slave to External Word Clock” in this application. See the M32 line, which is configured Master in this example: Specifications Connectors RJ45, Gigabit Ethernet 1 GBit/s, ‘PRIMARY’ and ‘SECONDARY’ 2 Input/Output Characteristics Input / Output channels Sample rates 32 / 32 44.
24 KLARK TEKNIK DN32-DANTE FEDERAL COMMUNICATIONS COMMISSION COMPLIANCE INFORMATION KLARK TEKNIK DN32-DANTE Responsible Party Name: MUSIC Group Research UK Limited Address: Klark Industrial Park, Walter Nash Road, Kidderminster. Worcestershire. DY11 7HJ. England. Phone Number: +44 1562 741515 DN32-DANTE This equipment complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2.
klarkteknik.
