Specification

2848 Corporate Parkway, Algonquin, IL 60102 T: 847.639.7272 Toll Free: 800.801.7832 www.4progressive.com
Manufactured by:
KLEEN KOTE 100
Water-based release agent with corrosion protection
Product Description
KLEEN KOTE is a water-based release agent that enables smooth concrete
surfaces, easy separation of forms/form liners from concrete, protects
vehicles, equipment and tools from concrete, mud, asphalt, fertilizer and
corrosion.
Uses
• Concrete Release
• Asphalt Release
• Mud/Mining Release
• Form/Formliner Release
• Rust Inhibitor
Advantages
• Low V.O.C. 13-17 g/L
• Certified Biodegradable
• Does NOT contain any phosphates, solvents or silicones
• Meets ASTM/Army Corps. Of Engineers Specs
• Meets/exceeds the 2014 SCAQM Rule #1113 requirements
• Easy to use
• Safe for use on all surfaces: rubber, metal, plastic,
electrical/wiring, glass, wood & motors
• Easy and clean stripping of formwork
• Provides a smooth, non-dusting/non-stained concrete surface
• Extends the life of equipment, vehicles and formwork
• Reduces costs associated with cleaning and maintaining
equipment, tools and formwork
• Inhibits rust
Product Data
Form
Appearance / Colors Concentrate: Amber viscous liquid at room temperature
Ready to Use: White liquid
Packaging • 32oz. bottle • 1gal. bottle • 3.5gal. pail
• 4.5gal. pail • 5gal. pail • 55gal. drum
• 275gal. tote
Storage
Storage Conditions / Concentrate: 60 months from date of production
Shelf Life if stored properly in original, unopened and
undamaged packaging (bottles, pails, drums,
totes) at temperatures between 40°F and 90°F.
Ready to Use: 18 months
Application Details
Dosage/Coverage
Mix KLEEN KOTE 100 with water at the specified application ratio.
Coverage rates are approximate and depend on the type and porosity
of the form surface. Use only clean containers that have not been used
for acids. Do NOT mix with diesel, fuels or oils.
Notes on Application /Limitations
• Prior to application, form surfaces should be thoroughly cleaned of all concrete,
rust and previous release agents.
• If forms/form liners have fresh oil or other release agents already applied, you
must cast or clean off previously applied products prior to applying KLEEN KOTE.
• The application can be applied in one coat with brush, roller or spray.
In order to achieve maximum benefit, KLEEN KOTE should be applied with a fine,
misting-type spray tip so that the application may be in a thin, uniform film.
• A second coat application may be necessary in case of highly absorbent formwork.
• Apply KLEEN KOTE to the entire formwork, including the back side to protect from
splatters.
• Over application will not produce better results and may cause dusting. Excess
product or puddles should be removed with a squeegee and absorbent rags.
• Allow KLEEN KOTE to change from white to clear before using treated formwork.
• KLEEN KOTE must be re-applied to the forms/ form liners after EACH use.
• KLEEN KOTE 100 is a concentrate that will not freeze, however once mixed,
KLEEN KOTE may freeze.
• KLEEN KOTE cannot be applied in rain, snow or ice but once applied, will not rinse
off in these conditions.
• A small test patch is recommended to ensure uniform coverage of KLEEN KOTE.
Precautionary Statements
• Keep container tightly closed. Avoid breathing dust/fume/mist/vapors/spray/aerosol.
• Wash hands thoroughly after handling. Do not eat, drink, or smoke when using
this product.
• Wear protective gloves/protective clothing/eye protection. Use PPE as required.
• Keep away from open flame or sources of ignition.
Additional precautions, safety information
and first aid are contained in the SDS.
Technical Data
Chemical Base A blend of mineral oil and other key ingredients
Vapor Density >5 , (AIR=1)
Viscosity
100 SUS @ 100°F (19cST @ 40°C)
Freezing Point Mixed: 32°F
Legal Notes
LEED Information
KLEEN KOTE Concentrate may contribute to LEED points based on the following
categories:
• MR-2 Construction Waste Management
• Shipped as a concentrate which reduces packaging by 90%
• Biodegradable
• Packaging materials including bottles, pails, drums, cartons, cardboard/paper inserts
and some pallets are recyclable
•MR-5 Regional Materials
• As a concentrate, the final manufacturing of the product is done on the jobsite
when water is added to make the product ready to use. The mix ratio range
1 to 11 through 1 to 15 parts Kleen Kote to water. This results in a product that
is over 90% water which has been added on-site.
• Typically one 3.5 gal. to 4.5 gal. pail of KLEEN KOTE Concentrate is required to
mix a 55 gal. barrel of ready to use product. Shipping a 40 lb./5 gal. pail to a
construction site is significantly more efficient than shipping a 500 lb./55 gal.
barrel.
• IEQ-4.2 Low Emitting Materials
This product has an extremely low VOC content and is biodegradable.
• 1 to 11 ratio – KLEEN KOTE Concentrate has a VOC content of 15 g/L
• 1 to 15 ratio – KLEEN KOTE Concentrate has a VOC content of 14 g/L
CONDITIONS OF SALE
Progressive Solutions Corporation (PSC) offers chemical products for sale subject and limited by this legal notice / warranty which may ONLY be varied by WRITTEN agreement
of a duly authorized corporate officer of PSC. No other representative of or for PSC is authorized to grant any warranty or to waive any limitation of liability set forth below.
All orders are accepted subject to our current terms of sale and delivery. Any purchase or purchase order terms are expressly rejected including terms which indicate shipment
as a manner of acceptance.
WARRANTY LIMITATION
MANUFACTURING DEFECTS
PSC warrants this product to be free of manufacturing defects. If the product, when purchased and used within the shelf life as determined by the date on the container
or carton is defective, PSC will replace the defective product with new product without charge to the purchaser. Product containers or cartons without dates are not covered
by ANY warranty. NO CLAIM OF ANY KIND SHALL BE GREATER THAN THE PURCAHSE PRICE OF THE PRODUCT IN WHICH DAMAGES ARE CLAIMED.
OTHER WARRANTIES
PSC makes NO OTHER WARRANTY, EITHER EXPRESSED OR IMPLIED, for it’s chemical products. NO WARRANTY in respect to merchantability or fitness for a particular purpose,
nor any warranty either expressed or implied, nor any liability whatsoever, shall be inferred either from this information, or from any written recommendations, or from any
other advice offered. NO CLAIM OF ANY KIND SHALL BE GREATER THAN THE PURCAHSE PRICE OF THE PRODUCT IN WHICH DAMAGES ARE CLAIMED.
INHERENT RISK
Purchaser assumes all risk associated with the use or application of the product. Any information and in particular, the recommendations relating application and use of PSC’s
products, are provided in good faith based on PSC’s current knowledge and experience of the products when properly stored, handled and applied under normal conditions in
accordance with PSC’s recommendations. Differences in materials, substrates and actual site conditions are such that the user of this product must test the product’s suitability
for the intended application and purpose. PSC reserves the right to change the properties of it’s products. Users should always refer to the most recent revision of the
Technical Data Sheet, Application Specific Instructions and SDS of the product(s) concerned, copies of which will be supplied upon request.
Concrete Forms - Ratio of 1 part KLEEN KOTE to 15 parts Water
Steel, Aluminum 2000 sq ft/gal
Polystyrene foam 2000 sq ft/gal
ABS Plastic 2000 sq ft/gal
Urethane Elastomeric liners 2000 sq ft/gal
Fiberglass 2000 sq ft/gal
HDO Plywood 2000 sq ft/gal
Concrete Forms - Ratio of 1 part KLEEN KOTE to 11 parts Water
MDO Plywood Forms 1500 sq ft/gal
EPS Foam 1500 sq ft/gal
Wood Forms 1000 sq ft/gal
LDO Plywood Forms 1000 sq ft/gal