Instructions / Assembly
VDV427-821 & VDV427-822
Instruction Manual
ENGLISH
VDV427-821 & VDV427-822
Manual de instrucciones
Manual de instruções
VDV427-821 e VDV427-822
VDV427-821 et VDV427-822
Manuel d'utilisation
Dwg Name: VDV427-821-139782 Dwg No: 139782
ECO No: 016620 Pkg Dwg Ref: 1662 Rev: B
Color Reference: N/A
139782 Rev 06/13 B
INSERTING BLADE
1. Align slot in center of punchdown blade with the pin located on
the inside of the punchdown tool’s barrel and insert blade (Fig. 1).
2. Rotate blade ¼ turn clockwise (Fig. 2).
Note: When blade is completely seated and locked, the cutting knife should
align with the yellow side of the tool; note “CUT” is imprinted on yellow side
of tool.
110 TYPE PUNCHDOWN INSTRUCTIONS
1. Insert the 110 terminating blade into the punchdown tool.
2. Choose the correct end of the blade depending whether or not the wire is to
be cut off. (Fig. 6 & 7 show use of the cutting end).
3. Select the proper force setting – LO for all 110 type connections.
4. Lay the wires in the wire slots (Fig. 5).
5. Slide the blade into the wire slot and verify the orientation of the punchdown
blade before moving to step 6 (Fig. 6). The "CUT" side of the blade should
face the end of the wire to be cut.
6. Push down on the cushion-grip end of the punchdown tool with the palm
of your hand until it clicks (Fig. 7).
7. Slide the blade out of the wire slot and make sure the wire is properly seated
in the bottom of the wire slot between the insulation displacement connector’s
(IDC) blades. Proper use of the punchdown tool should ensure this is done
correctly, but it is always a good idea to verify and test.
ADJUSTING PUNCHDOWN FORCE
Note: Arrow on “Impact” dial aligns with selected force setting.
1. To adjust from LO to HI, rotate dial to the right (Fig. 3).
2. To adjust from HI to LO, rotate dial to the left (Fig. 4).
Note: See table below for recommended force settings.
Impact
(force)
Setting
66 Panel/Block/
Terminal
110 Cross-Connect Panels/
Blocks/Keystone Jacks
LO
24-26 gauge conductors All
HI
23 and larger
gauge connectors
NOT RECOMMENDED
66 TYPE PUNCHDOWN INSTRUCTIONS
1. Insert the 66 terminating blade into the punchdown tool.
2. Choose the correct end of the blade depending whether or not the wire
is to be cut off. (Fig. 9 & 10 show use of the cutting end).
3. Select the proper force setting depending on the application (See table).
4. Lay the wires in the openings on the post (Fig. 8).
5. Slide the blade over the post and verify orientation of the punchdown blade
before moving to step 6 (Fig. 9). The "CUT" side of the blade should face the
end of the wire to be cut.
6. Push down on the cushion-grip end of the punchdown tool with the palm of
your hand until it clicks (Fig. 10).
7. Slide the blade off of the post and make sure the wire is properly seated
at the bottom of the post between the insulation displacement connector’s
(IDC) blades. Proper use of the punchdown tool should ensure this is done
correctly, but it is always a good idea to verify and test.
Punchdown tools and accessories
Description Cat. No.
Cushion-Grip Impact Punchdown Tool Kit – 110/66
VDV427-822
Cushion-Grip Impact Punchdown Tool – 110/66
VDV427-821
Wire Pick
VDV327-103
Dura-Blade
TM
110/66 Cut Combination Punchdown Blade
VDV427-104
Punchdown Tool Reach Extension Collar
VDV427-018
Ferramentas de impacto e acessórios
Descrição Nº cat.
Kit da ferramenta de impacto com cabo
emborrachado – 110/66
VDV427-822
Ferramenta de impacto com cabo emborrachado – 110/66
VDV427-821
Puxador de fio
VDV327-103
Lâmina de ferramenta de impacto de corte combinada
110/66 Dura-Blade™
VDV427-104
Anel de extensão de alcance da ferramenta de impacto
VDV427-018
Herramienta para ponchadora y accesorios
Descripción Cat. N.º
Juego de herramientas para ponchadora de impacto
con mango acojinado – 110/66
VDV427-822
Herramienta para ponchadora de impacto con
mango acojinado - 110/66
VDV427-821
Recolector de alambre
VDV327-103
Cuchilla Dura-Blade™ 110/66 para ponchado
y corte combinados
VDV427-104
Collarín de extensión de alcance para herramienta ponchadora
VDV427-018
Outils d'insertion et accessoires
Description N° de cat.
Trousse d’outil d'insertion à choc avec manche
Cushion-Grip – 110/66
VDV427-822
Outil d'insertion à choc avec manche Cushion-Grip – 110/66
VDV427-821
Crochet à fil
VDV327-103
Lame combinée 110/66 Dura-BladeTM pour outil d'insertion
VDV427-104
Collet de rallonge pour outil d'insertion
VDV427-018
Warranty / Garantía / Garantia / Garantie :
www.kleintools.com/warranty
B
5 6 8
B
A
B
A
B
4
6
8
7
A
C U T
B
5 6 8
B
A
4
6
8
7
B
A
B
5 6 8
B
A
4
6
8
7
C U T
Fig.9
B
5 6 8
B
A
B
A
B
4
6
8
7
A
C U T
B
5 6 8
B
A
4
6
8
7
B
A
B
5 6 8
B
A
4
6
8
7
C U T
Fig.10
B
5 6 8
B
A
B
A
B
4
6
8
7
A
C UT
B
5 6 8
B
A
4
6
8
7
B
A
B
5 6 8
B
A
4
6
8
7
C U T
Fig. 8
Fig. 2
Fig. 1
Broche
I
M
P
A
C
T
I
M
P
A
C
T
Fig. 3
I
M
P
A
C
T
I
M
P
A
C
T
Fig.4
B
5 6 8
B
A
B
A
B
4
6
8
7
A
C U T
B
5 6 8
B
A
4
6
8
7
B
A
B
5 6 8
B
A
4
6
8
7
C U T
Fig. 5
B
5 6 8
B
A
B
A
B
4
6
8
7
A
C U T
B
5 6 8
B
A
4
6
8
7
B
A
B
5 6 8
B
A
4
6
8
7
C U T
Fig. 6
B
5 6 8
B
A
B
A
B
4
6
8
7
A
C U T
B
5 6 8
B
A
4
6
8
7
B
A
B
5 6 8
B
A
4
6
8
7
C U T
Fig. 7
US Patent Pending
Patente pendiente en EE. UU.
Patente pendente nos EUA
Brevet Américain en instance
REMOVING BLADE
1. Rotate blade ¼ turn counter-clockwise and pull gently (Fig. 2).
2. Remove blade (Fig. 1).
VDV427-821-139782ART.indd 1 5/2/14 8:45 AM