Cut Sheet

All dimensions are in inches and (millimeters).
205205205
AUTO
A
AC
CL200
Electrical Test & Measurement
www.kleintools.com
See page 296 for additional information on warnings.
Cat. No. Kit Contains Wieight
69149 15.1 oz. (428 g)
Cat. No. Batteries Height Width Depth Weight
MM300 2 x AAA 6" (152 mm) 3.07" (78 mm) 1.78" (45 mm) 8.1 oz. (230 grams)
NCVT-1 2 x AAA 5.5" (140 mm) .72" (16 mm) N/A 1.6 oz. (46 g)
receptacle
tester
N/A 2.75 (70 mm) 1.5 (38 mm) 1" (25 mm) 1.3 oz. (37 grams)
test leads N/A 41" (1,041 mm) N/A N/A 3.2 oz. (90.7 grams)
Multimeters
Electrical Test Kit
•
The MM300 multimeter was developed to withstand daily wear and tear on the job site, and has a safey rating of CAT III 600V, Class 2, Double insulation.
•
The NCVT-1 has a bright green LED to indicate the tester is working; it changes to red and warning tones sound when voltage is detected.
•
NCVT-1 has a digitally-controlled ON/OFF power button and auto power-off feature to conserve and extend battery life.
•
Receptacle tester detects wiring configurations and indicates correct wiring, open ground, open hot, open neutral,
hot/ground reversed; it does not indicate quality of ground, multiple hot wires, or a combination of defects.
•
Includes visual and audible continuity indicators up to 25Ω.
•
Includes test leads and batteries.
8ZX5
See information about the MM300 multimeter on page 204 and
for the non-contact voltage tester on page 207.
NEW!
NEW!
Multimeter Replacement Fuses
Cat. No. For Use With Fuse Type
69191 MM1000, MM1300, MM2000, MM2300, MM6000 F 11A / 1000V
69192 MM1000, MM1300, MM2000, MM2300, MM6000 F 440mA / 1000V
69193 MM100 Fuse Kit F10A / 500V, F250mA / 250V
69194 MM200 Fuse Kit F10A / 500V, F400mA / 250V
New Test and Measurement Instruments
69031 MM300 5x20 200MA 600V NEW!
69032 MM300, MM400 6x32 10A 600V NEW!
69033 MM400 5x20 500MA 600V NEW!
69034 MM600, MM700 10x38 10A 1000V NEW!
69035 MM600, MM700 6x32 500MA 1000V NEW!
6919269033
Multimeter Specifications
Cat. No. CAT Rating Batteries Height Width Depth Weight Included Accessories
MM300 CAT III 600V 2 x AAA 6" (152 mm) 3.07" (78 mm) 1.78" (45 mm) 8.1 oz. (230 grams) Test leads and batteries NEW!
MM400 CAT III 600V 2 x AAA 6" (152 mm) 3.07" (78 mm) 1.78" (45 mm) 8.1 oz. (230 grams) Test leads, batteries and thermocouple NEW!
MM600 CAT IV 600V 2 x AAA 7" (178 mm) 3.54" (90 mm) 2.1" (53 mm) 14.6 oz. (414 grams) Carrying case, test leads, thermocouple, NEW!
and batteries
MM700 CAT IV 600V 2 x AAA 7" (178 mm) 3.54" (90 mm) 2.1" (53 mm) 14.6 oz. (414 grams) Carrying case, test leads, thermocouple,
NEW!
batteries, and alligator clips
WARNINGS:
To ensure safe operation and service of the tester, follow these instructions. Failure to observe these warnings can result in severe injury or death.
• Before each use, verify meter operation by measuring a known voltage or current.
• Never use the meter on a circuit with voltages that exceed the category based rating of this meter.
• Do not use the meter during electrical storms or in wet weather.
• Do not use the meter or test leads if they appear to be damaged.
• Ensure meter leads are fully seated, and keep fingers away from the metal probe contacts when making measurements.
• Do not open the meter to replace batteries while the probes are connected.
• Use caution when working with voltages above 60V DC, or 25V AC RMS. Such voltages pose a shock hazard.
• To avoid false readings that can lead to electrical shock, replace batteries if a low battery indicator appears.
• Unless measuring voltage or current, shut off and lock out power before measuring resistance or capacitance.
• Always adhere to local and national safety codes. Use individual protective equipment to prevent shock and arc blast injury where hazardous live conductors are exposed.