Cut Sheet
Table Of Contents
- Introduction
- Cushion-Grip Screwdriver Sets
- Switch Drive Handle Systems
- Cushion-Grip Screwdrivers
- Multi-Bit
- Replacement Parts
- Magnetic Screwdriver Bit Set
- Journeyman™ Screwdrivers
- Plastic-Handle Screwdrivers
- Screw-Holding
- Specialty Driver Set
- Torque
- Cushion-Grip Nut Driver Sets
- Switch Drive Nut Driver Handle System
- Cushion-Grip Nut Drivers
- Plastic-Handle Nut Drivers
- Tapping Tools and Awls
- Spring Tools
www.kleintools.com
6969
Screwdrivers, Nut Drivers
& Accessories
All dimensions are in inches and (millimeters).
Conduit Reamers
Conduit-Fitting and Reaming Screwdriver
Additional Features:
•
Hooded-blade design keeps tip from slipping out of screws,
especially when tightening hard-to-reach conduit fittings.
Thicker hood is designed for rugged use.
•
Reams and smooths 1/2" (13 mm), 3/4" (19 mm), and 1" (25 mm) thin-wall
conduit ends to protect wire and permit correct installation of fittings.
•
Reams both the inside and outside of the conduit at the same time.
•
Replaceable reaming blade is now held in place with a 1/16" (1.5 mm) set screw.
85191
Cat. No. Tip Size Shank Length Overall Length Weight (lbs.)
85191 5/16" (8 mm) 2-1/2" (64 mm) 7-1/2" (191 mm) .50
19353 conduit reamer replacement blade kit .01
Power Conduit Reamer
Cat. No. Description Weight (lbs.)
85091 conduit reamer drill head for 1/2" (13 mm), 3/4" (19 mm), 1" (25 mm) conduit .33 lbs.
19353 conduit reamer replacement blade .01 lbs.
SQ2115 #2 square recess replacement bit, 15-pack .01 lbs.
85091
•
Ream 1/2" (13 mm), 3/4" (19 mm), and 1" (25 mm) conduit and install fittings
in a fraction of the time.
•
Designed to fit into power drill chucks and quick release adapters; impact ready.
•
Includes precision engineered replaceable reaming blade.
•
Replacement blades are available and the only approved blade for use in this tool.
•
Replacement bits are available but any standard 1/4" hex bit will work.
Conduit Reamer
Cat. No. Conduit Capacity Weight (lbs.)
19352 1/2" (13 mm), 3/4" (19 mm), 1" (25 mm) .20
19353 conduit reamer replacement blade kit for 19352 .01
19352
•
Locks onto screwdrivers; reams and smooths thin-wall conduit.
•
Reams ID and OD at the same time.
•
Two set-screws for round- and square-shank screwdrivers.
•
Fits up to 3/8" (10 mm) keystone-tip screwdrivers.
•
NOT for use on power tools.
Specialty Cushion-Grip Screwdrivers
Screw-Holding Screwdrivers
Additional Features:
•
Starts and drives screws
with one hand when working
in hard-to-reach spaces.
Cat. No. Tip Type Tip Type Shank Length Overall Length Weight (lbs.)
32215 cabinet 1/4" (6 mm) 7" (178 mm) 11-1/4" (276 mm) 0.32
32216 Phillips #2 7" (178 mm) 11-1/4" (276 mm) 0.32
32215
NOTE
:
Read and follow safety instructions in power tool owner’s manual.
See page 310 for additional information on warnings.