INSTALLATION MANUAL AIR CONDITIONER WIRED CONTROL MODEL: KJR-12B/DP(T)-F-1 KJR-12B/DP(T)-E-1A KJR-12B/DP(T)-E-2 RCW8(P/N:7ACEL1706) Thank you very much for purchasing our product. Before using your unit, please read this manual carefully and keep it for future reference.
● This manual gives detailed description of the precautions that should be brought to your attention during operation. ● In order to ensure correct service of the wired controller please read this manual carefully before using the unit. ● For convenience of future reference, keep this manual after reading it.
CONTENTS 1. SAFETY PRECAUTIONS......................................................................... 1 2. INSTALLATION ACCESSORY.................................................................. 2 3. INSTALLATION METHOD.........................................................................
1. SAFETY PRECAUTIONS Read the safety precautions carefully before installing the unit. Stated below are important safety issues that must be obeyed. WARNING Means improper handling may lead to personal death or severe injury. CAUTION Means improper handling may lead to personal injury or property loss. WARNING Please entrust the distributor or professionals to install the unit. Installation by other persons may lead to imperfect installation, electric shock or fire.
2. INSTALLATION ACCESSORY Select the installation location Don’t install at the place where cover with heavy oil, vapor or sulfureted gas, otherwise, this product would be deformed that would lead to system malfunction. Preparation before installation 1. Please confirm that all the following parts you have been supply. No. Name Qty.
2. INSTALLATION ACCESSORY Precaution of install the wire controller 1. This manual provides the installation method of wire controller. Please refer to the wiring diagram of this installation manual to wire the wire controller with indoor unit. 2. The wire controller working in low voltage loop circuit.
3. INSTALLATION METHOD 1.Wired remote controller structure size figure 21 19.5 13.1 85.5 120 51.1 120 50 Fig 3-1 2.
3. INSTALLATION METHOD 3.Wiring figure 5-core wire The connective wires group Indoor display board 5-core or 4-core wire Fig 3-3 Connect the female joint of wires group from the mainboard with the male joint of connective wires group. (See Fig.3-3) Please connect the other side of connective wires group with the male joint of wires group leads from wire controller. (See Fig.3-3) 4.
3. INSTALLATION METHOD 4. Fasten the back plate of the wire controller For exposed mounting, fasten the back plate on the wall with the 3 screws (M4×20) and plugs. (Fig.3-5) Back plate Screws (M4×20) Fig 3-5 For flush-mounting, fasten the back plate on the switch box with 2 screws (M4×25) and fasten it on the wall with 1 screw (M4×20). (Fig.3-6) Switch box Back plate Screw (M4×20) Screws (M4×25) Fig 3-6 NOTICE Put on a flat surface.
3. INSTALLATION METHOD 5. Wiring Top side wire outlet A. For exposed mounting, four outletting positions. There are three need cutting. Right side wire outlet Left side wire outlet Bottom side wire outlet Cutting place of top side wire outlet Cutting place of left side wire outlet Cutting place of right side wire outlet Fig 3-7 B.
3. INSTALLATION METHOD 6.Reattach the upper part of the wire controller After adjusting the upper case and then buckle the upper case; avoid clamping the wiring during installation. (Fig 3-10) Fig 3-10 All the pictures in this manual are for explanation purpose only. Your wire controller may be slightly different .The actual shape shall prevail.
The Klimaire logo is a registered Trademark of Klimaire Products inc. Copyright 2016 Klimaire Products Inc. 2190 NW 89 Place, Doral, FL 33172 - USA Tel: (305) 594 - 4972 www.klimaire.com Fax (305) 675-2212 sales@klimaire.com The design and specifications are subject to change without prior notice for product improvement.
