OWNER’ S MANUAL AIR CONDITIONER WIRED CONTROL MODEL: KJR-12B/DP(T)-F-1 KJR-12B/DP(T)-E-1A Thank you very much for purchasing our product. Before using your unit, please read this manual carefully and keep it for future reference.
● This manual gives detailed description of the precautions that should be brought to your attention during operation. ● In order to ensure correct service of the wired controller please read this manual carefully before using the unit. ● For convenience of future reference, keep this manual after reading it. ● The wired controller will reset to factory setting with auto mode, auto fan and 24°C(76°F) setting temperature when the air conditioner restarts after power failure.
CONTENTS 1. SAFETY PRECAUTION.............................................................................. 1 2. SUMMARIZE............................................................................................... 2 3. FUNCTION SUMMARY............................................................................... 2 4. NAME AND FUNCTION OF INDICATORS ON THE WIRE CONTROLLER............................................................................................ 3 5. INSTALLATION METHOD.................
1. SAFETY PRECAUTIONS The following contents are stated on the product and the operation manual, including usage, precautions against personal harm and property loss, and the methods of using the product correctly and safely. After fully understanding the following contents (identifiers and icons), read the text body and observe the following rules. Identifier description Identifier Meaning Warning Means improper handling may lead to personal death or severe injury.
Warning Warning Delegate installation Please entrust the distributor or professionals to install the unit. The installers must have the relevant know-how. Improper installation performed by the user without perm ission may cause fire, electric,shock, personal injury or water leakage. Forbid Do not spray flammable aerosol to the wire controller directly. Otherwise, fire may occur. Forbid Do not operate with wet hands or let water enter the wire controller. Otherwise, electric shock may occur. 2.
4. NAME AND FUCTION OF INDICATORS ON THE CONTROLLER 1 Operation mode indication 3 Follow me function 4 ON/OFF indication 1 5 Fan speed indication 2 1 2 Timer ON/OFF 12 6 Lock 7 Temperature display zone ① Operation mode indication: When press " MODE " button, the following mode can be selected in circle. Auto →Cool →Dry→Heat→Fan only→Auto. For cooling only model,heat mode is skipped. ② Timer : When adjust setting on time or only on time is set, the "ON" is lighted.
the same as setting temperature. It is available under cooling, heating, auto mode. ④ ON/OFF indication : When it is on, the icon display, otherwise it is extinguished. ⑤ Fan speed indication : There are four fan modes : low, middle, high, auto. For some models, no middle fan then the middle fan is seen as high speed. ⑥ Lock: When the " LOCK " button is pressed, the icon appear and other buttons is unable, press again, the icon disappear.
When a wire controller is needed, a small 5-way terminal should be added,fix an infrared emitter with gumwater near the receiver on the switch board. Connect its anode and cathode to A and B,and +5V, GND, RUN to C, D, E on the switch board. 6.
① Mode botton: When press this botton,the operation mode change as the following sequence: →AUTO → COOL→DRY→HEAT→FAN Remark: For the cooling only model, the heating mode is skipped. ② Timer on button : Press this button, timer on function is active. Then every press, the time increase 0.5h, after 10h, 1h increasement after each press. If cancel this Function, just set it to "0.0" . ③ Timer off button: Press this button, timer off function is active.Then every press, the time increase 0.
NOTE: Press and hold UP and DOWN buttons together will alternate the temperature display between the °C & °F scale. ⑩ Swing button: Used to set the airflow direction. Hold down this button for 2 seconds to activate auto swing feature.
COOL/HEAT/FAN MODE OPERATION 1. Press "MODE" button, select "COOL" , "HEAT" or "FAN ONLY" mode. 2. Press temperature adjust button to select setting temp. 3. Press "FAN SPEED" button to select high/mid/low/auto. 4. Press "ON/OFF" button, indoor unit operation lamp on, it works in selected mode. Press "ON/OFF" button again, it stops to work. Remark: When in fan mode, no temperature can be set. DRY OPERATION 1. Press " MODE " button, select " DRY " mode. 2.
TIMER ON AND TIMER OFF BOTH 1. Set timer on time corresponding step1 and 2. 2. Set timer off time corresponding step1 and 2. as the as the 3. Timer off time must be longer than 8. TECHNICAL INDICATION AND REQUIREMENT EMC and EMI comply with the CE certification requirements. timer on time. 4. 0.5 second after setting, the wire controller send information.the setting is finished. CHANGE TIMER If there is a need of changing timer time, press corresponding button to revise it.
The Klimaire logo is a registered Trademark of Klimaire Products inc. Copyright 2016 Klimaire Products Inc. 2190 NW 89 Place, Doral, FL 33172 - USA Tel: (305) 594 - 4972 www.klimaire.com Fax (305) 675-2212 sales@klimaire.com The design and specifications are subject to change without prior notice for product improvement.
