Remote Control

ManualsBrandsKlimaire ManualsAir ConditionersKSIV Series 12000 BTU Single Zone Mini Split System

Table Of Contents

SERIES

Mark of Superior Quality

AUTO

FAN

ON/OFF

SILENCE

TIMER

OFF

MODE

FAN

TEMP

SLEEP

TURBO

SELF

CLEAN

LED

SLEEP Button

NOTE: While the unit is running under SLEEP

mode, it would be cancelled if MODE, F

SPEED or ON/OFF button is pressed.

Active/Disable sleep function. It can

maintain the most comfortable temperature

and save energy. This function is available

on COOL, HEAT or AUTO mode only .

For the detail, see “sleep operation” in

“USER´S MANUAL”.

MODE Button

Press this button to modify the air conditioner

mode in a sequence of following:

AUTO

COOL

DRY

HEAT

FAN

NOTE: Please do not select HEAT mode if the

machine you purchased is cooling only type.

Heat mode is not supported by the cooling

only appliance.

AUTO LOW MED HIGH

FAN Button

Used to select the fan speed in four steps:

NOTE: You can not switch the fan speed in

AUTO or DRY mode.

SELF CLEAN Button

Active/Disable Self Clean function.

Under SELF CLEAN mode, the air

conditioner will automatically clean and dry

the Evaporator and keep it as fresh for the

next operation.

TURBO Button

Active/Disable Turbo function. Turbo function

enables the unit to reach the preset temper-

ature at cooling or heating operation in the

shortest time (if the indoor unit does not

support this function, there is no

corresponding operation happened when

pressing this button.)

UP Button ( )

Push this button to increase the indoor

temperature setting in 1F increments to 86ºF.

DOWN Button ( )

Push this button to decrease the indoor

temperature setting in 1ºF increments to 62ºF.

NOTE: Temperature contol is not available

in Fan mode.

NOTE: Press and hold UP and DOWN buttons

together for 3 seconds will alternate the temper-

ature display between the ºC & ºF scale.

TIMER ON Button

Press this button to initiate the auto-on

time sequence. Each press will increase

the auto-timed setting in 30 minutes

increments. When the setting time displays

10.0, each press will increase the auto-

timed setting 60 minutes increments.

To cancel the auto-timed program, simply

adjust the auto-on time to 0.0.

SILENCE/FP Button

Active/Disable SILENCE function. If pushing

more than 2 seconds, the “FP” function will

be activated, pushing more than 2 seconds

again to disable.

When the Silence function is activated, the

compressor will operate at low frequency

and the indoor unit will bring faint breeze,

which will reduce the noise to the lowest

level and creat a quiet and comfortable room

for you. Due to low frequency operation of

compressor, it may result in insuﬃcient

cooling and heating capacity.

LED Button

Disable/Active indoor screen Display. When

pushing the button, the indoor screen display

is cleared, press it again to light the display.

SWING Button

Used to stop or start horizontal louver auto

swing feature.

DIRECT Button

Used to change the louver movement and set

the desired up/down air ﬂow direction.

The louver changes 6° in angle for each press.

FOLLOW ME Button

Push this button to initiate the Follow Me

feature, the remote display is actual

temperature at its location. The remote

control will send this signal to the air

conditioner every 3 minutes interval until

press the Follow Me button again. The air

conditioner will cancel the Follow Me feature

automatically if it does not receive the signal

during any 7 minutes interval.

TIMER OFF Button

Press this button to initiate the auto-oﬀ time

sequence. Each press will increase the auto

-timed setting in 30 minutes increments.

When the setting time displays 10.0, each

press will increase the auto-timed setting

60 minutes increments. To cancel the auto-

timed program, simply adjust the auto-oﬀ

time to 0.0

SWING DIRECT

ON/OFF Button

This button turns the air conditioner ON

and OFF.

Remote

Control

Activates/Disables freeze protection”FP”

or HOME-AWAY function. It can only be

activated during the heating operation.

(only when the setting mode is HEAT).

The unit will operate at high fan speed with the

temperature automatically set to 46 F. The

display window of indoor unit will display FP.

For the unit without display area, the Defrost

indicator light will be keeping on for 2 seconds

Keeps the room over freezing temperature.

UP TO 19 SEER

Summary of content (9 pages)

PAGE 1
SERIES UP TO 19 SEER Remote Control 1 ON/OFF Button 2 SILENCE/FP Button 8 This button turns the air conditioner ON and OFF. Active/Disable SILENCE function. If pushing more than 2 seconds, the “FP” function will be activated, pushing more than 2 seconds again to disable. When the Silence function is activated, the compressor will operate at low frequency and the indoor unit will bring faint breeze, which will reduce the noise to the lowest level and creat a quiet and comfortable room for you.
PAGE 2
REMOTE CONTROLLER ILLUSTRATION
PAGE 3
Remote Controller Specifications CONTENTS Model RG57A6/BGEFU1 Rated Voltage 3.0V(Dry batteries R03/LR03 2) Remote controller Specifications................................................... 2 Signal Receiving Range 8m Operation buttons .................. ......................................................... 3 Environment 23 OF~140 OF Indicators on LCD .......................................................................... 6 How to use the buttons .......................................
PAGE 4
Operation of buttons 1 2 ON/OFF Button This button turns the air conditioner ON and OFF. Operation of buttons 7 UP Button( ) Push this button to increase the indoor temperature setting in 1oF increments to 86oF. DOWN Button( ) Push this button to decrease the indoor temperature setting in 1oF increments to 62oF. MODE Button Press this button to modify the air conditioner mode in a sequence of following: AUTO COOL DRY HEAT NOTE Temperature contol is not available in Fan mode.
PAGE 5
Operation of buttons Indicators on LCD 10 TIMER OFF Button Press this button to initiate the auto-off time sequence. Each press will increase the auto -timed setting in 30 minutes increments. When the setting time displays 10.0, each press will increase the auto-timed setting 60 minutes increments. To cancel the autotimed program, simply adjust the auto-off time to 0.0 Information are displayed when the remote controller is powered up.
PAGE 6
How to use the buttons How to use the buttons Dehumidifying operation Auto operation 2 3 ON/OFF SILENCE FP 1 MODE TIMER ON NOTE 1. In the Auto mode, the air conditioner can logically choose the mode of Cooling, Fan, and Heating by sensing the difference between the actual ambient room temperature and the setting temperature on the remote controller. 2. In the Auto mode, you can not switch the fan speed. It has already been automatically controlled. 3.
PAGE 7
Timer operation Press the TIMER ON button can set the auto-on time of the unit. Press the TIMER OFF button can set the auto-off time of the unit. To set the Auto-on time. ON/OFF SILENCE FP MODE TIMER ON TEMP TIMER OFF FAN SLEEP TURBO SELF CLEAN SWING DIRECT LED FOLLOW ME 1 2 1. Press the TIMER ON button. The remote controller shows TIMER ON, the last Auto-on setting time and the signal "H" will be shown on the LCD display area. Now it is ready to reset the Auto-on time to START the operation. 2.
PAGE 8
TIMER ON TIMER OFF (Off Start Stop operation) This feature is useful when you want to start the air conditioner before you wake up and stop it after you leave the house. TIMER OFF (Auto-off Operation) The TIMER OFF feature is useful when you want the unit to turn off automatically after you go to bed. The air conditioner will stop automatically at the set time. Stop On Set 10 hours later Example: To stop the air conditioner in 10 hours. 1.
PAGE 9
Handling the remote controller Location of the remote controller. 8m Use the remote controller within a distance of 8 meters from the appliance, pointing it towards the receiver. Reception is confirmed by a beep. CAUTIONS The air conditioner will not operate if curtains, doors or other materials block the signals from the remote controller to the indoor unit. Prevent any liquid from falling into the remote controller. Do not expose the remote controller to direct sunlight or heat.