MANUEL DE L’UTILISATEUR Support Technique / Garantie Pour toutes questions techniques sur votre produit. Pour tout problème de fonctionnement ou de panne. Contactez notre support technique : Site : www.klipad-support.com (Questions / Notices / Support / Informations) Email : Support@kliverfrance.
IMPORTANT - LE PRODUIT NE COMPRENDS PAS ASSEZ DE MEMOIRE, POUR L’UTILISER PLEINEMENT VOUS DEVEZ IMPERATIVEMENT INSTALLER UNE CARTE MEMOIRE TF (Micro SD) Capacité Jusqu'à 32 Go - POUR UTILISER LA FONCTION WIFI SUR LES APPAREILS MOBILES VOUS DEVEZ INSTALLER L’APPLICATION MYANYCAM. ELLE DOIT ETRE TELECHARGEE SUR LE PLAY-STORE (ANDROID) OU SUR L’APPLE STORE. - VOUS DEVEZ VOUS RENDRE SUR LE SITE : www.myanycam.
Avant d’utiliser cet appareil, veuillez lire attentivement les présentes instructions. Ce manuel est destiné à vous orienter dans l’utilisation de cet appareil en particulier. Attention : 1. Veuillez respecter strictement les législations nationales pertinentes. Ce produit ne peut être utilisé à des fins illégales ; en cas contraire, l'utilisateur subirait les conséquences correspondantes. 2. Veuillez insérer la carte dans le sens correct afin d'éviter d'endommager la carte ou le DVR. 3.
CHARGEMENT DE LA BATTERIE 1. Branchez la petite fiche du câble USB dans le port USB situé sur la partie inférieure de la caméra. Branchez l'extrémité opposée dans un port USB disponible de votre ordinateur. 2. Lorsque l'ordinateur est allumé, la batterie se recharge comme indiqué par le témoin lumineux indicateur de chargement. 3. Le témoin restera allumé tout au long du cycle de charge et s'éteindra quand le chargement se sera achevé. 4.
ENGLISH Ok Mic Status Charging indicator Micro SD Slot Speaker Micro USB Port Shoulder Belt hook FRENCH Ok Micro Témoin de niveau de charge Fente Micro SD Haut-parleur Port Micro USB Crochet pour sangle à l’épaule Cloud mode Direct mode Video mode Picture mode Mode button Power button Mode Cloud (Nuage) Mode direct (WIFI) (connection au smartphone) Mode vidéo Mode photo Stents base Base de la tour Spring clip magnet base Shoulder belt base Pince à ressort Base magnétique Base de la sangle à l’épaule
Mode direct III. Mode P2P La procédure de recharge et la mise SOUS/HORS tension 1. Chargement Insérez une source d'alimentation de 5 V dans l'interface Micro USB de l’appareil. L'appareil va se connecter et se recharger. Le témoin lumineux rouge indiquant le processus de chargement est généralement situé sur le panneau supérieur. Lorsque le niveau d’énergie est insuffisant pendant le processus d’utilisation, le témoin rouge du panneau avant clignote à intervalles rapides.
Remarque : Veuillez appuyer sur le bouton OK et sur le bouton MODE simultanément. L'appareil va se réinitialiser et retourner au mode normal en cas d'échec ou dans l'impossibilité d'effectuer la mise sous/hors tension. Si vous avez oublié le mot de passe du dispositif correspondant pour l'application, vous pouvez appuyer longuement sur la touche OK pendant 8 secondes en AP (Mode direct). Le mot de passe par défaut du dispositif sera alors rétabli. Nous vous recommandons de réinitialiser l'appareil.
L'écran tactile affiche quatre touches virtuelles, comme suit : Cliquez sur cette icône pour activer le haut-parleur En cliquant sur cette icône, vous pouvez contrôler le son ambiant. Appuyez sur le bouton HAUT/BAS pour régler le volume sonore. Avec le système Android, le haut-parleur est activé par défaut.
5. Mode CLOUD / RESEAU : **** QUICKSTART **** Connectez le sport Cam et le smartphone ensembles comme dans le mode WIFI. Allez dans l’application MYANYCAM sur le smartphone. Ouvrer le menu CAMERA SETTING (roue en bas a droite) Ouvrer le menu SELECT WIFI Choisir votre réseau local (box internet ) Rentrer votre clé de sécurité wifi (box internet) Revenir au menu, puis fermer l’application.
A. Caméra Cliquez sur le bouton Reproduction pour visionner les vidéos en temps réel. Si vous cliquez sur l'écran, vous verrez apparaître le bouton de menu émergent de la fonction lors de la visualisation des vidéos en temps réel : Cliquez sur cette icône pour activer . Cela envoie le signal sonore au téléphone mobile. Appuyez sur le bouton HAUT/BAS pour régler le volume sonore. Cliquez sur cette icône pour activer . Cela envoie le signal sonore du téléphone mobile à l'appareil.
Système Android Le mode vidéo et le mode photo sont identiques au système IOS 1. Mode direct (Mode WIFI) Allumez le caméscope et passez en mode direct lorsque le téléphone ou dispositif a installé le logiciel d'application. Le témoin lumineux de mode s'allume et reste allumé. Ouvrez le réseau WLAN pour rechercher le nom de MyanyCamxxx. Le mot de passe pour la connexion est « 12345678 » et le témoin lumineux bleu s'allume et reste allumé lorsque la connexion a été effectuée correctement.
L'écran tactile affiche quatre touches virtuelles, comme suit : Cliquez sur cette icône pour activer le haut-parleur En cliquant sur cette icône, vous pouvez contrôler le son ambiant. Appuyez sur le bouton HAUT/BAS pour régler le volume sonore. Avec le système Android, le hautparleur est activé par défaut.
téléphone mobile peut ajouter plusieurs caméras SN. Vous pouvez ajouter de nombreuses caméras. Si vous souhaitez supprimer une caméra dans la liste, appuyez longuement sur la caméra correspondante sélectionnée et vous verrez apparaître le dialogue de suppression du menu contextuel. Suivez les instructions pour effectuer ces opérations. E) Après avoir ajouté la caméra, vous pouvez cliquer sur la caméra souhaitée dans la liste des caméras. Différentes options sont disponibles, à savoir : 1.
VI. Spécifications de la caméra Capteur d'image Ouverture de l'objectif Plage de mise au point Standard sans fil Mode sans fil PC WIFI Vidéo Mouvement WIFI vidéo Support de stockage Batterie Spécifications du système informatique HD720P/30fps F2.2 FOV : 90 grand angle 25 cm --- 00 EEE802.
pendant 8 secondes. L'appareil va rétablir les configurations par défaut. Veuillez réinitialiser l'appareil et effectuer de nouveau la configuration. Cette fonction est en cours d'amélioration. 4. En mode direct, l'appareil apparaît dans la liste. Pourquoi la connexion ne peut-elle pas être effectuée correctement dans tous les cas ? Ce téléphone mobile s'est connecté avec le même nom que le caméscope WIFI. Le téléphone mobile a mémorisé le mot de passe de la dernière connexion du caméscope.