KLIPSCH PROFESSIONAL IN-CEILING LOUDSPEAKERS IC-400-T I IC-500-T-SC I IC-525-T I IC-650-T I IC-800-T OWNER'S MANUAL Klipsch
IMPORTANT SAFETY INSTRUCTIONS READ these instructions. KEEP these instructions. HEED all warnings. FOLLOW all instructions. DO NOT use this apparatus near water. CLEAN ONLY with dry cloth or lightly damped cloth. DO NOT block any ventilation openings. Install in accordance with the manufacturer's instructions. 8. DO NOT install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9.
WARNING: Neglect to follow the safety and installation instructions may cause malfunctions resulting in property damage and personal injury. A Klipsch recommends that only qualified personnel install its loudspeaker systems. At all times, be sure that adequate safety factors are observed. Due to the weight and size of the components involved, potential damage could occur if devices were to become unattached. A The included tile-bridge must be used when installing into suspended ceilings.
KLIPSCH PROFESSIONAL IN-CEILING SPEAKERS .. IC-400-T IC-500-T-SC ... ( ..
INSTALLATION All Klipsch Professional In-Ceiling speakers include a tilebridge for use when installing the loudspeaker into suspended ceiling or wherever additional reinforcement of the ceiling material is required. The tilebridge and loudspeaker are designed such that installation may be accomplished where access above the ceiling is not possible or may be difficult. ~fl I I I I I I I I I I I I I I I I I I I I The tilebridge is composed of three parts: a reinforcement ring and two rails.
INSTALLATION ,,,,. / - -- ~ I TEMPLATE ' I ' \ \ \ To install your speaker cut a hole in the ceiling using either the cardboard cutout template provided with your speakers or consult the measurements shown. Pull wiring through hole. ' ' __ .,,,, / IC-4OO-T, IC-525-T, IC-5OO-T 09.125" IC-65O-T 010.125" IC-8OO-T 012.
To Install the tilebridge, fold the rail side of the ring back upon itself using the spring tensioner on the reinforcement ring to allow insertion into the cutout hole. Once it is inserted into the cutout hole, release the reinforcement ring such that it unfolds back to its normal position. Position tilebridge over cutout hole, and insure that the tile rails rest on the t-grid struts.
INSTALLATION FOR IC-5OO-T-SC ONLY + 70/100v Common + 8 ohm (7.5 ohm for IC-650-T) The wiring compartment is intended as a termination point for the audio circuit. Access to the compartment is gained by removing the terminal cover located on the back of the speaker. (For the IC-5OO-T-SC, the terminal is located on the side of the speaker) The terminal cover will accept the appropriate conduit/wire adapter.
[ Insert the speaker into the cutout hole. With a #2 Phillips screwdriver, tighten the four dog clamps until they are seated securely against the ceiling surface. Do not overtighten.
INSTALLATION For installations using 70V/100V input connection, set the switch on the front panel to the desired setting. For applications where IC-400-T tap selectable 8 Ohm (7.5 Ohm for IC-650-T) impedance is desired, the switch should be set to IC-500-T-SC tap selectable 8 Ohm (7.5 Ohm for IC-650-T). Note: The speaker comes from the factory set at the lowest output setting (high impedance).
SEISMIC TAB Using the flat of your hand, insert grille into speaker frame making sure it is securely seated and flush. Aseismic tab, located on the back of the speaker, is used as a secondary security point. Some construction codes may require its use. To utilize the seismic tab, run a support wire from a secure point in the ceiling and attach it to the tab. Be sure to consult the construction codes in your area. Klipsch recommends the use of this tab in all installations as a secondary means of support.
lipscti KEEPERS OF THE SOUND 3502 WOODVIEW TRACE, iNDIANAPOLIS, IN, USA KLI PSC H.