CP SERIES OWNER’S MANUAL
RECOMMENDED RECEIVER/AMPLIFIER POWER TO USE WITH KLIPSCH CP SPEAKERS A speaker can be damaged just as easily with too little power as with too much power. A general rule is when you raise the volume level on a receiver/amplifier past the “one half” (or “12 o’clock” position with a marked volume knob), that receiver/amplifier is now starting to work beyond its capabilities, sending harmful distortion that can damage any speaker, no matter how many watts that speaker is rated to accept.
HOOKING SPEAKERS UP TO AN AMPLIFIER/RECEIVER (CONTINUED) IF YOU WISH TO USE TWO PAIRS OF KLIPSCH CP SERIES SPEAKERS ON ONE AMPLIFIER/RECEIVER WE RECOMMEND ONE OF TWO METHODS: SPK A SPK B L R _ _ _ PARALLEL WIRING TWO PAIRS TO 4Ω CAPABLE AMP/RECEIVER METHOD 2 Method 2: IF YOUR AMP/RECEIVER IS RATED TO 4 OHMS OR LESS make a parallel wire connection as shown from the amp/receiver’s right and left speaker terminals.
SUGGESTED SPEAKER PLACEMENT X X X STEREO ROOM PLACEMENT EXAMPLE AS SURROUND SPEAKERS ROOM PLACEMENT EXAMPLE Speakers same distance apart(X) as their distance to main listening positition 5.1 surrond: 2 side speakers 7.1 surround: 2 side/2 rear speakers (all speaker 5-6’ (1.
SUGGESTED SPEAKER PLACEMENT (CONTINUED) If speakers are covering a very large listening area (i.e. large patio/deck) you may be able to send a mono signal (L+R channel) to both speakers so that all listeners hear everything even if far from one speaker. See amplifier/receiver manual to see if it allows this.
CP SERIES Thank you for your purchase of the Klipsch CP Series speakers! They are designed to both withstand the rigors of outdoor use while also complimenting any indoor décor as either a stereo pair or surround speakers in a home Theater system. The included, unique wall bracket provides for easy horizontal or vertical wallmounting and even allows for a tight mounting tucked into a corner for a highly aesthetic look that also adds bass output. Shelf or table placement is an added option.
SPEAKER DIMENSIONS WITH/WITHOUT INCLUDED BRACKETS CP-6 CP-4 5.5” (14.0cm) 7.0” (17.8cm) 6.9” (17.5cm) 5.5” (14.0cm) 8.8” (22.4cm) 7.2” (18.3cm) 4.7” (11.9cm) BEFORE SPEAKER INSTALLATION/CONNECTION If wall mounting speakers, run speaker wire behind wall to mounting spots (if desired) If wall-mounting with brackets you will also need: a) A level b) A pencil c) A Philips screwdriver (#2 size) d) Two #10 or #12 2.5-3 inch (4-5cm) Pan Head Screws for mounting into wall stud OR minimum 10 lb.
STEP 1 Typical Wall-Mounting With Included Bracket (Level not included) V H H OR V If Wall/Wall Corner or Ceiling/Wall Corner Mounting With Included Bracket V H V OR Choose speaker location and run speaker wire to location. Use included template and a level to mark bracket hole locations where speaker will be mounted.
STEP 2 Remove rubber terminal cover on speaker front and push speaker wire through middle channel on speaker back until pushed through speaker front where cover was.
STEP 2 (CONTINUED) A. B. OR Speaker Wires Use #10-#12, 2.5-3 INCH Pan Head Screws C. IF USING SUPPLIED BRACKET A. Run speaker wire through hole in bracket back and attach wall bracket to wall B. Slide speaker partially onto bracket arms and channel wire from back to front D. C. D.
MOUNTING OPTIONS 45˚ 45˚ OR OR WALL CEILING OR WALL 45˚ 45˚
STEP 3 A. Lowest Dril Torque Setting B. 1 2 3 4 5 A. Connect Speaker Wires to Speaker Terminals with screwdriver or DRILL SET ON LOWEST TORQUE SETTING WITH #2 PHILIPS SCREWDRIVER BIT. Observe the correct polarity. Usually, red wire is positive (+) and black is negative (–). It does not matter which wire is connected to the positive or negative terminal as long as the connections are consistent on all speakers in the same system. Make sure both wires are pushed inside slot and replace terminal cover.
STEP 4 STEP 5 TEST SOUND: Play music through speaker to make sure connections are tight and polarity is correct Once speaker is in the final position and tested, attach grill by pressing grill into channel encircling speaker front *SPEAKER GRILL REMOVAL: Use included grill removal tool, insert into a top corner and gently pull out. Repeat on a corner next to first one pulled, then pull out grill gently with hand. NOTE: the grill is designed to fit snug on speaker to both remain on and to remain tight.
PAINTING THE SPEAKERS Paint speaker and bracket top/ bottom caps separately. 1. First, clean speaker cabinet and bracket top/bottom caps with mild solvent or mild detergent/water 2. Then create a paint mask for speaker front (baffle) by tracing speaker grill on sheet of thicker, non-porous paper then cutting paper around tracing. 3. Place grill paper mask on front of speaker (over baffle) making sure to also cover grill channel; secure with double sided tape. Do not put tape on woofer.
CP-4 SPECIFICATIONS FREQUENCY RESPONSE1 2 CP-6 SPECIFICATIONS FREQUENCY RESPONSE1 80Hz-22kHz +3/-6 dB 2 70Hz-22kHz +3/-6 dB POWER HANDLING 50 w (200 peak) POWER HANDLING 75 w (300 peak) SENSITIVITY3 91 dB @ 1 watt/1 meter SENSITIVITY3 94 dB @ 1 watt/1 meter NOMIMAL IMPEDANCE 8 ohms NOMIMAL IMPEDANCE 8 ohms TWEETER .75" (1.9cm) aluminum dome tweeter TWEETER .75" (1.
Scan the QR Code to view the Klipsch CP Series Owner’s Manual in all languages. OR GR - Handbuch in Deutsch: klipsch.com/cpmanual PR - Manual em Português: klipsch.com/cpmanual IT - Manuale in Italiano: klipsch.
3502 WOODVIEW TRACE, INDIANAPOLIS, IN, USA KLIPSCH.COM ©2013, Klipsch Group, Inc. Klipsch Group, Inc. is a wholly-owned subsidiary of Voxx International Corporation.
IMPORTANT SAFETY INSTRUCTIONS! Klipsch 1. READ these instructions. 2. KEEP these instructions. 3. HEED all warnings. FOLLOW all instructions. 5. DO NOT use this apparatus near water. 6. CLEAN ONLY with dry cloth. WARNING: Do Not Open! Risk of Electrical Shock. Voltages in this equipment are hazardous to life. No user-serviceable DO NOT block any ventilation openings. Install in accor- parts inside. Refer all servicing to qualified service personnel. 7.
5~ 1 Q)il -"'<..> 0 e= To mount speaker vertically in comer PUTTING BRACKET ON LEFT WALL against comer put THIS SIDE flush in corner on left wall and mark vertical pilot holes Cl: L&.l e &:D _. L&.l a:i _. ~ ~ L&.l s L&.l :E ~ Cl: L&.l ~ Cl) ~ s~ c 0 o::r:: -~ 'S :i!E: 0 0 PllotHol• PllotHol• ftVertlool ~ = s~ c 0 -~ o.S! ::r::a:: To mount speaker vertically in corner PUTTING BRACKET ON RIGHT WALL against corner put THIS SIDE flush in corner on left wall and mark ::.