Tech Support: 1-800-KLIPSCH State-of-the-art LIGHT & SOUND One LightSpeaker® 5 installs in 15 minutes or less! OWNER’S MANUAL Note: The LightSpeaker® is an add on unit to an existing LightSpeaker® System. You need a LightSpeaker® Transmitter to supply audio and control the lights on this unit. The Transmitter and Remote discussed in the manual are sold separately.
Tech Support: 1-800-KLIPSCH The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
Tech Support: 1-800-KLIPSCH IMPORTANT SAFETY INSTRUCTIONS 1. Read these instructions. Keep these instructions. Heed all Warnings. Follow all instructions. 2. Do not use this apparatus near water. The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on apparatus. 3. Clean only with a dry cloth. 4. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 5.
Tech Support: 1-800-KLIPSCH Congratulations Thank you for choosing a LightSpeaker® 5 from Klipsch®. You have chosen one of the most unique, patented, audio systems in the world. With proper installation and operation, you will enjoy years of trouble-free use. Klipsch® sells numerous loudspeakers for use inside or outside your home. For the complete Klipsch® product line, visit the Internet at: www.klipsch.com.
Tech Support: 1-800-KLIPSCH Table of Contents LightSpeaker® 5 Overview..................................................................6 What is in this box...................................................................................8 Step 1 - Where will you install..........................................................9 Step 2 - Check your connector type.............................................9 Step 3 - Test fit your LightSpeaker® 5......................................
Tech Support: 1-800-KLIPSCH LightSpeaker® 5 Overview This wireless LightSpeaker® 5 is intended to install into any home easily and without any expensive and complicated wiring. You can install a unit in your home in a few minutes and not have to worry about repairing walls or ceilings. Plus there is no climbing into attics or wriggling into crawl spaces! LightSpeakers® deliver great sound into any room in your house, using your existing wiring and your recessed lighting fixtures.
Tech Support: 1-800-KLIPSCH Your system can use up to 8 LightSpeakers® to provide audio and lighting to your entire home. You can even divide your home into two unique areas where different music sources, sound and lighting control allow you to add music with integrated “green” lighting to places you only dreamed of having it before. There’s no wiring and no big (or small) boxes.
Tech Support: 1-800-KLIPSCH Take just a minute to be sure you have everything you need to install your additional wireless distributed audio LightSpeaker® 5 from Klipsch®. Large & Small Trim Rings Lens LightSpeaker® 5 Note: The LightSpeaker® 5 is an add on unit to an existing LightSpeaker® System. You need a LightSpeaker® Transmitter to supply audio and control the lights on this unit. The Transmitter and Remote discussed in the manual are sold separately.
Tech Support: 1-800-KLIPSCH Instruction Manual Step 1: Decide which light will be replaced with LightSpeaker® 5. Your Klipsch® LightSpeaker® 5 has been specifically designed to cover large areas, however if the location of your fixtures allow you to do so, you should think about how you use your room and where you are likely to spend most of your time. Then choose the fixtures that are most evenly spaced to your preferred listening position.
Tech Support: 1-800-KLIPSCH Step 3: Test fit your LightSpeaker® 5. Your LightSpeaker® 5 is designed to fit directly into most 5“ (R30) and 6“ (R40) down light cans by simply removing the existing light and, in the same manner as a light bulb, re-installing your LightSpeaker® 5 in its place. You may simply test fit your LightSpeaker® 5. If your LightSpeaker® 5 fits directly into your recessed lighting fixture without any modifications you can skip forward to Step 6.
Tech Support: 1-800-KLIPSCH B) The thinner one is used when installed into a 5” fixture. As long as the trim ring covers the edges of the lighting fixture and any rough drywall edges you may use either trim ring; it will not affect the performance of your LightSpeaker® 5. Step 5: Adjusting the SimpleTabs™. Your LightSpeaker® 5 is equipped with a unique mounting system.
Tech Support: 1-800-KLIPSCH If you are installing into a 6” recessed lighting fixture, rotate each of the SimpleTabs™ out to position “A” on the top of the LightSpeaker® 5 unit. SimpleTabsTM Step 6: Setting the Zone and L/R Stereo Switches. A) Set the zone switch on the back of the LightSpeaker® 5 to one, unless you are setting up a two zone system. For more on zones see Complete System Manual or go to www.Klipsch.com.
Tech Support: 1-800-KLIPSCH B) Set the left/right stereo switch. “L” if it is the left speaker, “R” if it is the right speaker. For additional information see Selecting LightSpeaker® 5 Locations on page 16. C) Your LightSpeaker® 5 system allows you to install up to 4 pair of (or 8 total ) speakers. If you are installing more than one pair of LightSpeakers® 5 you will probably want to divide your home into zones. See Complete System Manual or go to www.Klipsch.com.
Tech Support: 1-800-KLIPSCH 1) Grasp the Edison Socket with one hand, and with the other hand screw the LightSpeaker® 5 into the socket on the pigtail. Be careful: Always turn the speaker not the socket. Turning the socket will twist up the pigtail and put unneeded stress on the connection. 2) Grasp the LightSpeaker® 5 by the light bridge (see section titled “Removing the Lens” below) and while holding it level and steady, firmly push it back into the lighting fixture.
Tech Support: 1-800-KLIPSCH Step 9: Enjoy your Lightspeaker®!Helpful Hints Installing and Removing the Lens: A) Removal BEFORE your LightSpeaker® 5 is installed. 1) While holding the LightSpeaker® 5 in the palm of your hand rotate the unit until one of the holding tabs is facing up. 2) Using a common screwdriver or other small flat object, gently push down and then out on the tab, easing it out through the opening in the LightSpeaker® 5 housing.
Tech Support: 1-800-KLIPSCH B) Removal of the lens AFTER your LightSpeaker® 5 has been installed. 1) There are three small indentations around the lens; with a small tip common screwdriver, nail file, paper clip or similar object, gently slip the tip into the indentation and pry the lens outward until the retaining tabs pull free. 2) To re-install the lens, align the tabs and the hole for the pairing LED, then push gently until the locking tabs snap into place.
Tech Support: 1-800-KLIPSCH Selecting LightSpeaker® 5 Locations Survey your home to determine the location of 5” and 6” recessed lighting fixtures. As long as these are wired to the home’s electricity through a common light switch, they should work perfectly. If you have multiple locations within one room, try to space the speakers as far as part as possible, this will provide the best stereo image and the best sound. In general, the maximum spacing of the speakers is determined by ceiling height.
Tech Support: 1-800-KLIPSCH LED Light • 10W super bright LED provides a sharp crisp light that is easy on the eyes. • LED outputs the light suitable to replace up to a 60W incandescent bulb • Long Lasting LED is rated for over 25,000 to 40,000 hours of use (15 to 20 years average use) • LED Light is fully dimmable and is controlled from either the remote or the light button on the transmitter Wireless Transmitter Receives a 2.
Tech Support: 1-800-KLIPSCH Loud Speaker • 2.5” high performance custom engineered woofer with Micro Cellulose Polymer treated cone material provides even coverage and smooth natural sounding audio reproduction • Integrated high frequency disperser. Accessories • Optional flange allows LightSpeaker® to fit into either 5” (R30) or 6” (R40) recessed lighting fixtures. • Frosted Lens is acoustically transparent 5” LightSpeaker® Specifications Woofer 2.
Tech Support: 1-800-KLIPSCH Possible causes of interference with your LightSpeaker® 5 A) Metal studs, in fact any metal wall material, can cause the signal to be diminished or lost. This may also be a problem if your wall paper happens to be a foil type or have metal fibers in it. B) Microwave ovens, when operating, may degrade or interrupt the signal from your transmitter. Usually this will only be a problem for those speakers in close proximity to the microwave.
Tech Support: 1-800-KLIPSCH Warranty - Home and Commercial Audio (U.S.) The Warranty below is valid only for sales to consumers in the United States. KLIPSCH, LLC (“KLIPSCH”) warrants this product to be free from defects in materials and workmanship (subject to the terms set forth below) for a period of two (2) years from the date of purchase for the LED light and one (1) years from the date of purchase for the rest of the components.
Tech Support: 1-800-KLIPSCH This Warranty does not cover product sold AS IS or WITH ALL FAULTS. REPAIRS OR REPLACEMENTS AS PROVIDED UNDER THIS WARRANTY ARE THE EXCLUSIVE REMEDY OF THE CONSUMER. KLIPSCH SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR BREACH OF ANY EXPRESS OR IMPLIED WARRANTY ON THIS PRODUCT.
Tech Support: 1-800-KLIPSCH THIS DEVICE COMPLIES WITH FCC RULES PART 15. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) This device must accept any interference received including that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
Tech Support: 1-800-KLIPSCH Klipsch Worldwide Corporate Headquarters 3502 Woodview Trace, Suite 200 Indianapolis, IN 46268 For more detailed installation instructions go to www.klipsch.com Klipsch Technical Support Toll Free: 1-800-KLIPSCH (1-800-554-7724) Monday - Friday, 8:00 AM - 5:30 PM EST E-mail: technicalsupport@klipsch.