REFERENCE FLOORSTANDING LOUDSPEAKERS OWNER'S MANUAL
REFERENCE SERIES IMPORTANT SAFETY INSTRUCTIONS UNPACKING AND ASSEMBLING THE SPEAKER NOTE: Although this loudspeaker can be unpacked and set up by a single person,a helper will make the job easier, not to mention safer, for speaker and owner alike. 1. READ these instructions. 2. KEEP these instructions. 3. HEED all warnings. 4. FOLLOW all instructions. 5. DO NOT use this apparatus near water. 6. CLEAN ONLY with dry cloth. 7. DO NOT block any ventilation openings.
obtain best performance from your speakers if you connect them to your amplifier or receiver with Monster Cable or similar quality wire available from your dealer. We recommend that you use 16-gauge or heavier stranded copper wire.Use a lower gauge (heavier) wire for longer runs to reduce the amount of amplifier power lost due to the wire’s resistance. On the back of each speaker are two sets of binding posts, one feeding the tweeter and the other the woofers.
REFERENCE SERIES Most pre-terminated speaker cables have color-coded connectors that make it easy to match output and inputs correctly. If yours do not,or if you are making your own out of paired,twoconductor wire,look for identifying marks on the insulation of the two conductors.Normally there will be printing,a stripe or a molded ridge along one of the conductors.
IMPORTANTES CONSIGNES DE SÉCURITÉ 1. LIRE ces instructions. 2. CONSERVER ces instructions. 3. RESPECTER tous les avertissements. 4. SUIVRE toutes les instructions. 5. NE PAS utiliser cet appareil à proximité de l’eau. 6. NETTOYER UNIQUEMENT avec un chif fon sec. 7. NE PAS OBSTRUER les ouïes de ventilation.Installerconformément auxinstructionsdu constructeur. 8.
REFERENCE SERIES Le câblage interne des enceintes Klipsch de la gamme Reference est effectué avec un câble de type Bandwidth Balanced™ Monster®.La technologie Bandwidth Balanced™ fait appel à des fils de cuivre de grande pureté et de différents diamètres,soigneusement sélectionnés et bobinés de façon à assurer une transmission optimale des signaux de différentes fréquences.
Reference de Klipsch est une enceinte utilisant toute la gamme de fréquences et pouvant donc être réglée sur Large dans le récepteur ou le processeur, sous le menu de configuration des enceintes.Mais si votre système comporte un bon caisson de graves amplifié,vous obtiendrez peut-être un meilleur fonctionnement d’ensemble en réglant les enceintes sur Small,ce qui dirige tous les graves vers ce caisson.Faites des essais pour trouver ce qui convient le mieux à votre système.
REFERENCE SERIES AUSPACKEN UND ZUSAMMENBAU DER LAUTSPRECHER WICHTIGER SICHERHEITSHINWEIS 1. LESEN Sie diese Anweisungen durch. 2. BEHALTEN Sie diese Anweisungen. HINWEIS: Obwohl dieser Lautsprecher von einer Person ausgepackt und aufgestellt werden kann,macht die Mithilfe einer weiteren Person die Arbeit sowohl für den Lautsprecher als auch dessen Besitzer einfacher und sicherer. 3. BEACHTEN Sie alle Warnhinweise. 4. FOLGEN Sie allen Anweisungen. 5.
Lautsprecher der Klipsch Reference-Serie sind intern mit Bandwidth Balanced™ Monster® Cable Kabel verdrahtet.Die Bandwidth Balanced™-Technologie verwendet mehrere Drähte aus hochreinen hochreinem Kupfer, die sorgfältig ausgewählt und verflochten wurden,um eine optimale Signalübertragung über den gesamten Frequenzbereich hinweg zu gewährleisten.
REFERENCE SERIES Standlautsprecher der Klipsch-Reference-Serie decken den gesamten Frequenzbereich ab und können im Lautsprecher-Setup-Menü Ihres Receivers oder Prozessors auf Large (groß) eingestellt werden. Wenn Ihr System aber einen guten Aktiv-Subwoofer enthält,können Sie die Gesamtsystemleistung wahrscheinlich dadurch verbessern,dass Sie die Einstellung Small (klein) wählen,damit der Subwoofer die tiefen Bassfrequenzen übernimmt. Testen Sie,was bei Ihrem System am besten funktioniert.
DISIMBALLAGGIO E MONTAGGIO DELL’ALTOPARLANTE LEGGERE QUESTE ISTRUZIONI NOTA:sebbene questo altoparlante possa essere disimballato e montato da una persona sola,lavorando in due si procederà più facilmente,con maggiore sicurezza e con minor ris chio di danni all’altoparlante stesso. 1. CONSERVARLE. 2. RISPETTARE tutte le avvertenze. 3. SEGUIRE tutte le istruzioni. 4. NON usare questo apparecchio vicino all’acqua. 5. PULIRE SOLO con un panno asciutto. 6. NON ostruire nessuna apertura per l’aria.
REFERENCE SERIES ANSCHLÜSSE Hinweis:Der korrekte Anschluss Ihrer Lautsprecher an den Verstärker oder Receiver ist entscheidend für eine gute Tonqualität.Folgen Sie bitte sorgfältig diesen Anweisungen. Schlechte Anschlüsse können zu Fehlfunktionen oder Beschädigungen des Verstärkers führen. Figure 2 Configurazione dell’impianto stereo per un’ampia copertura.
nessun trefolo di un conduttore tocchi il terminale cilindrico a cui è connesso l’altro conduttore o i trefoli di quest’ultimo.La mancata osservanza di questa precauzione può causare un malfunzionamento dell’amplificatore o anche danneg giarlo. Pin. Molti tipi di cavi da altoparlante preassemblati sono terminati con spinotti metallici (pin).Allentate i dadi di una coppia di terminali cilindrici fino a esporre i fori praticati su di essi e infilate i pin nei fori.
REFERENCE SERIES INSTRUÇÕES IMPORTANTES DE SEGURANÇA DESEMBALAGEM E MONTAGEM DA CAIXA ACÚSTICA Observação: Embora esta caixa acústica possa ser desembalada e montada por uma pessoa,duas pessoas tornariam a tarefa mais fácil,além de mais segura para a caixa e para o proprietário. 1. LEIA estas instruções. 2. GUARDE estas instruções. 3. SIGA todos os avisos. 4. SIGA todas as instruções. 5. NÃO USE este equipamento próximo de água. 6. LIMPE SOMENTE com um pano seco. 7.
Sistema stereo de dois canais. A figura 2 mostra um arranjo típico para um sistema stereo de dois canais.Um bom ponto de partida é a criação de um triângulo equilátero com vértices nas caixas e na sua posição de ouvinte.Dependendo do tamanho da sala e do arranjo da mobília,pode ser conveniente fazer a distância da posição de audição à linha entre as caixas acústicas maior ou menor, mas tente mantê-la centralizada,de forma que você fique à mesma distância de cada caixa.
REFERENCE SERIES A maneira mais fácil de assegurar que suas caixas acústicas estão ligadas com os fios em fase é conectar sempre os terminas positivo e negativo de saída no seu amplificador ou receiver aos correspondentes terminais de entrada nas caixas acústicas:positivo (+,vermelho) ao positivo e negativo (-,preto) ao negativo.(Veja a Figura 4.) A maioria dos cabos para caixas acústicas pré-fabricados tem conectores coloridos que facilitam a correspondência correta das entradas e saídas.
IMPIMPORTANTES INSTRUCCIONES DE SEGURIDAD 1. 2. 3. 4. 5. 6. 7. LEA estas instrucciones. GUARDE estas instrucciones. RESPETE todas las advertencias. SIGA todas las instrucciones. NO use este dispositivo cerca del agua. LÍMPIELO SOLAMENTE con un paño seco. NO bloquee los orificios de ventilación.Instálelo de acuerdo con las instrucciones del fabricante. 8.
REFERENCE SERIES Sistema estéreo de dos canales. La figura 2 muestra una disposición de altavoces común de un sistema estéreo de dos canales.Crear un triángulo equilátero con los altavoces y la posición del oyente es un buen punto de partida.Dependiendo del tamaño de la sala y de la disposición de los muebles,puede ser conveniente disminuir o aumentar la distancia entre la posición del oyente y la línea entre los altavoces,pero trate de que el oyente quede a la misma distancia de los dos altavoces.
La manera más fácil de que los altavoces queden conectados en fase es conectar siempre los terminales de salida positivo y negativo del amplificador o receptor a los terminales de entrada correspondientes de los altavoces:positivo a positivo ("+" de color rojo) y negativo a negativo ("–" de color negro).(Vea la figura 4). La mayoría de los cables de altavoz con terminales tienen conectores de colores que facilitan la correspondencia correcta entre entradas y salidas.
Figure 1
Figure 2 X=Y=Z Figure 3 Figure 4
Figure 5
Register your new Klipsch product now at www.klipsch.com! Cut along dotted line and mail. For multiple speaker purchases, please fill out only one warranty card. Name: Street Address: City/State/Zip: Home Phone: Work Phone: E-mail Address: Would you like to receive the latest product updates and news via e-mail? ❑ Yes ❑ No Product Purchase Model and serial number must be included to honor your warranty card. For multiple speaker purchases,please fill out only one warranty card.
3502 Woodview Trace, Suite 200 Indianapolis, Indiana 46268 USA 1. 800 . KLIPSCH • www.klipsch.com Make sure you return your warranty For your records: card so that we may keep you up-to-date on new Klipsch products Model: and promotions. If you have any questions, contact your local Date Purchased: authorized Klipsch dealer.