STEREO POWER AMPLIFIER SE84ZS OWNERS MANUAL Decware High Fidelity Engineering Co. 1202 N.E.
lightning flash with arrowhead, within an equilateral triangle, is intended to alert the user to the presence of uninstalled “dangerous voltage” within the product’s enclosure that may be of risk of electric shock to persons. AVIS RISQUÉ DE CHOC ELECTRIC-NE PASOUVRIR. WARNING- TO REDUCE RISK OF FIRE OR ELECTRICAL SHOCK, DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE. IMPORTANT SAFETY INSTRUCTIONS! PLEASE READ THEM BEFORE OPERATING THIS EQUIPMENT. 1 2 3 4 5 6 7 8 Read these instructions.
Thank You By purchasing the Zen Triode Select amplifier you have illustrated a desire to rise past the normal hi-end hype and own a truly exceptional piece. It is a product based on the old school way of doing things when it was fashionable to push quality to an art form. Your amplifier was hand-built by the very best artisans who have perfected the craft through the experience of building well over one thousand amplifiers, each one at a time. Table of Contents Safety Instructions........................
Introduction and Performance Features Important Information Fuse location / Information 1 The fuse is integrated into the IEC power cord connector at the back of the SE84ZS. 2 3 4 5 6 Caution: To prevent electrical shock make sure that the AC POWER CORD IS NOT CONNECTED TO THE SE84ZS when inserting or removing Vacuum Tubes, as there are hazardous voltages present at the pins of the Tube Sockets. When Vacuum Tubes are installed or removed make sure to seat them properly in the tube sockets.
OUTPUT TUBE WARNING The SE84ZS is designed to use either EL84 output tubes or SV83 output tubes. No adjustments are needed when switching from one to the other. Of the type SV83 tubes carrying the Svetlana name there is one batch known to be questionable and ARE NOT RECOMMENDED for use in this amplifier. picture above.
INPUT TUBE INFORMATION WHERE EVERYTHING GOES The SE84ZS is designed to use your choice of three different input (or signal) tubes. Below are the tube locations, input jack configuration and power switch location. The input switch, one for each channel, changes between direct and variable inputs. It always points to the active jack. For example on the left side of the amp, moving the input switch to the right would select the variable input for that channel.
INTRODUCTION You now own one of the best SET amplifiers in the world! Unlike the stereotypes associated with single ended triode designs, the SE84ZS has many unique features that set it apart from the rest. It’s point-to-point construction, lack of circuit boards, and signal path consisting of only a single capacitor and two resistors means nothing sold today is more transparent or honest.
DIMENSIONS The SE84ZS amplifier is 7.25 inches wide by 14.75 inches deep with a height of 6.5 inches. With the jacks vertically mounted at the rear of the amplifier, it is possible to push the amp all the way to the rear of a shelf. However, we recommend keeping a 2 inch spacing on all sides and at least 6 to 10 inches of space above the amplifier. Avoid closed cabinets. The better the ventilation around your amplifier the cooler it will run.
STEREO / MONAURAL OPERATION HOW TO OPERATE To run the amplifier in Stereo, simply connect the left and right input jacks to your source or preamp and the left and right output binding posts to your speakers. If using the variable inputs, the volume control located at the front of the amplifier will control the output level of both channels at the same time. After finding an appropriate place for the amplifier you can install the tubes and connect the speaker cables.
SPECIFICATIONS • • • • • • • • • • • • • • • • • • • • • • • • • Weight 13 lbs. ea. Dimensions Circuit type 8.5" H x 7.250" W x 14.0" D Single ended Class A Triode Power output 2.3 watts RMS into 4 ohms 5 watts RMS into 8 ohms when bridged NOTE: Power increases as ohms decrease Stable into 1 ohm speaker loads Input voltage 2.0 volts for full output Noise / Hum Less Response 20 Hz ~ 20 kHz than 1.
to 47K plate to 47K plate B+ to output tansformers 1K 50 W DALE YELLOW US transformer shown 10 K 10K YELLOW/BLACK 6 .8 K 1 w a t t YELLOW RED BLACK 8 4, 4 6N1P or 6922 4 5 5 5 SV83 GRN 3 amp fuse 40 uf 450 volt ATOM CAP 40 uf 450 volt ATOM CAP 2 ~ 20 uf 250 volt ATOMCAPS 5U4 6 RED BLACK 2 4 RED/YELLOW 3.3uf 400v Solen poly 3.
