/2In. Mini Air Regulator Owner’s Manual WARNING: Read carefully and understand all ASSEMBLY AND OPERATION INSTRUCTIONS before operating. Failure to follow the safety rules and other basic safety precautions may result in serious personal injury.
Thank you very much for choosing a Klutch™ product! For future reference, please complete the owner’s record below: Serial Number/Lot Date Code: ________________________________ Purchase Date: ____________________________________________ Save the receipt, warranty, and this manual. It is important that you read the entire manual to become familiar with this product before you begin using it. This air regulator is designed for certain applications only.
Table of Contents Intended Use .......................................................................................................................................... 4 Technical Specifications ...................................................................................................................... 4 Important Safety Information ............................................................................................................... 4 Specific Operation Warnings .......................
Intended Use One of the most commonly used air line accessories, regulators are used to maintain a steady outlet pressure, unaffected by variations/fluctuations in the inlet pressure. Regulators step down the air line pressure and can be set at any desired pressure below the inlet air pressure. With an aluminum die cast body, these are designed with a non-raising “press to lock” adjusting knob for locking at any set pressure.
this equipment for a purpose for which it was not intended. Industrial or commercial applications must follow OSHA requirements. ⚠WARNING WORK AREA SAFETY Inspect the work area before each use. Keep work area clean, dry, free of clutter, and well-lit. Cluttered, wet, or dark work areas can result in injury. Using the product in confined work areas may put you dangerously close to other cutting tools and rotating parts.
product with a damaged part. Store the air regulator when it is not in use. Store it in a dry, secure place out of the reach of children. Inspect the tool for good working condition prior to storage and before re-use. Use only accessories that are recommended by the manufacturer for use with your product. Accessories that may be suitable for one product may create a risk of injury when used with another tool.
Main Parts of Product Ref # Description Qty. 1 2 3 4 5 6 7 8 9 10 11 12 12.1 12.2 13 14 15 16 16.
Assembly Instructions 1. Install in a clean/ acid free atmosphere. 2. Flush the piping for dirt, dust, and other foreign particles. 3. Use proper thread sealant for taper threads to create a leak-proof connection. 4. Screw the Inlet/Outlet pipe with the respective port. 5. Open the inlet valve/ switch on the air supply. 6. When using (G) parallel thread nipples, check the length of the thread from the given table. Thread Size Tightening Torque, Lb.
Maintenance 1. Before dismantling the unit, exhaust the air in the line completely. 2. Dismantle the components and clean them in kerosene and blow with compressed air. 3. Check for damages in the O-rings (15), (16.1), (17) and at sealing areas in the valve cone rubber, spherical relieving seating, seating area of the housing, etc. Replace if needed or clean and reassemble. 4. For assembly of the unit: Apply general purpose grease on the O-rings (15), (16.
Parts Diagram Page 10 of 13
Parts List Reference 1 2 3 4 5 6 7 8 * * * * 9 10 11 12 12.1 12.2 13 14 15 16 16.1 17 18 Item Description Knob Locknut Indicator Ring Philip Head Screw Bonnet Bearing Washer Adjusting Screw Assembly Main Spring 0.2 - 2 BAR (3 - 28 PSI) 0.2 - 4 BAR (3 - 58 PSI) 0.5 - 7 BAR (8 - 100 PSI) 0.
Limited Warranty Northern Tool and Equipment Company, Inc. ("We'' or '"Us'') warrants to the original purchaser only ("You'' or “Your”) that the Klutch product purchased will be free from material defects in both materials and workmanship, normal wear and tear excepted, for a period of one year from date of purchase. The foregoing warranty is valid only if the installation and use of the product is strictly in accordance with product instructions.
Distributed by: Northern Tool & Equipment Company, Inc. Burnsville, Minnesota 55306 www.northerntool.