Heavy-Duty Welding Fabrication Table with Fix-Up Kit Owner’s Manual WARNING: Read carefully and understand all ASSEMBLY AND OPERATION INSTRUCTIONS before operating. Failure to follow the safety rules and other basic safety precautions may result in serious personal injury.
® Thank you very much for choosing a Klutch product! For future reference, please complete the owner’s record below: Serial Number/Lot Date Code: ________________________________ Purchase Date: ____________________________________________ Save the receipt, warranty, and this manual. It is important that you read the entire manual to become familiar with this product before you begin using it. This welding table and kit is designed for certain applications only.
Table of Contents Intended Use .......................................................................................................................................... 4 Packaging Contents .............................................................................................................................. 4 Technical Specifications ...................................................................................................................... 4 Important Safety Information .................
Intended Use The Klutch Heavy-Duty Welding Fabrication Table and Fix-Up Kit gives you a steady, flame-proof steel surface for welding parts and components. The table is designed for conductivity so you can connect your welding clamp directly to the welding table, safely out of the way of slag and spatter. The adjustable angle and fence give you a variety of welding options.
flammable liquids, gases, or dust. Do not allow the product to come into contact with an electrical source. The tool is not insulated and contact will cause electrical shock. Keep children and bystanders away from the work area while operating the tool. Do not allow children to handle the product. Be aware of all power lines, electrical circuits, water pipes, and other mechanical hazards in your work area.
Specific Operation Warnings ⚠WARNING Always wear the proper protective equipment including ANSI Z87.1 compliant eye protection, a welding helmet, and welding gloves. Do not exceed the rated load capacity of 600 lb. Never sit or stand on the welding table. Use only on a level, hard surface. Inspect before each use. Do not use if parts are damaged. Keep the table clean for optimal performance. Wipe away dust and debris from the table top and legs. Not for use by or around children.
To use in the Full Assembly configuration, follow these instructions. If the Leveling Feet are attached to the welded Table Top Frame (short legs), remove the four feet and set aside. 1. Assemble the Long Leg (3) and Leg Brace (4). Place the Leg Brace in the upright position. Slip all four Leg Braces (4) into the holes on the Long Leg. It has 4 different height holes. Note: Use the same height holes to make sure the Leg Brace will be on the same level. 2.
Tool Kit: Clamps and Components Page 8 of 14
Assembly Options Before Each Use ⚠WARNING Inspect the general condition of the welding table. Check for loose hardware, misalignment, binding of parts, or cracked and broken parts.
Operating Instructions ⚠WARNING Always wear the proper protective equipment including ANSI Z87.1 compliant eye protection, a welding helmet, and welding gloves. Do not exceed the rated load capacity of 600 lb. Tighten all bolts before adding load. Be aware of dynamic loading! Sudden load movement may briefly create excess load causing product failure. Never sit or stand on the welding table. Use only on a level, hard surface. Inspect before each use.
Troubleshooting Use the table below to troubleshoot problems before contacting service personnel or your local dealer. If the problem continues after troubleshooting, call your local dealer for assistance. Failure The welding table stands unevenly. Possible Cause Corrective Action The screws are loose. Check and tighten all hardware. The feet are uneven. Adjust the feet until the table is steady.
Parts List Part Number 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 Part Description Table Top (with bottom frame) Short Leg Long Leg Leg Brace Leveling Foot Bolt Nut M8 Leveling Foot Nut M10 Stop Bars V-Blocks Stop Bars-cover Plate Threaded Adaptors V-Blocks-Spacers Inserta Clamp Bolt M10 Nut for Inserta Clamp M12 Quantity 1 4 4 1 4 16 16 4 4 8 4 4 4 4 8 4 Replacement Parts For replacement parts and technical questions, please call Customer Service at 1-800-222-5381.
Limited Warranty Northern Tool and Equipment Company, Inc. ("We'' or "Us'') warrants to the original purchaser only ("You'' or "Your") that the Klutch product purchased will be free from material defects in both materials and workmanship, normal wear and tear excepted, for a period of one year from date of purchase. The foregoing warranty is valid only if the installation and use of the product is strictly in accordance with product instructions.
Distributed by: Northern Tool & Equipment Company, Inc. Burnsville, Minnesota 55306 www.northerntool.