Manual

ManualsBrandsKMC Controls ManualsSensorsHPO–5213

HPO–5211/5212/5213 1 Installation Guide

Mounting

Linkage to Barber-Colman Valves

1. Thread 1/4-28 jam nut (1) onto valve stem (5) until

3/8" of valve stem is above the nut.

2. Thread stem extension (2) onto valve stem (5) and

tighten against jam nut (1).

3. Thread nut (3) as far as possible onto stem extension

(2).

4. Placeatwasher(4)ontopofnut(3)(onHPO–5211

andHPO–5212linkageonly).

5. Screwlinkage(6)ontovalve.Tightenaluminum

bonnet adaptor (8) against valve mounting nut (13).

6. Thread2setscrews(7)inevenlyuntilscrewscontact

atsonbrassbonnet.Donotfullytightenscrewsto

atsonbonnet.

7. Loosen2screws(12)androtatelinkage(6)to

desiredpositioninrelationtovalvebody.Tighten2

screws(12).

8. Whilefacinglever(9),rotatelevercounterclockwise

untilconnectingrod(10)contactslowerstemnut(3).

9. Thread upper stem nut (11) onto stem extension (2)

until1/16"to1/8"ofstemextensionisvisibleabove

nut (11).

10.Rotatelever(9)clockwisetoliconnectingrod(10)

upandaroundatsonupperstemnut(11).

11.Whileholdingconnectingrod(10)withwrench

tokeepfromtwisting,tightenlowerstemnut(3)

against connecting rod.

12. Rotate lever (9) until valve stem is in full up

position.Loosensetscrewsonleverhuband

reposition so that the end of the lever handle is just

insidethelesideofthelinkagehousing.Tighten2

setscrewsonleverhub.

13. Proceed to appropriate actuator mounting

instructions.

Installation Guide

Valve-Actuator Linkage Kit

HPO–5211/5212/5313

Dimensions in

inches (mm)

Barber-Colman Valve Models

Valve Sizes (Medium temperature must not exceed 250° F)

1/2" to 1-1/4" 1-1/2" to 2"

VB-111-0-3-1 through VB-111-0-3-9

Use the HPO-5211 if using the MEP–5000 actuators.

Close-Offs = 1/2" @ 81#

3/4" @ 81#

1" @ 56#

1-1/4" @ 30#

Use the HPO-5212 if using the MEP–1200 actuators.

Close-Offs = 1/2" @ 362#

3/4" @ 362#

1" @ 288#

1-1/4" @ 178#

Not Available

VB-921X-0-4-1 through VB-921X-0-4-11

Use the HPO–5213 with the MEP–1200 actuators.

Close-Offs = 1-1/2" @ 66#

2" @ 32#

VB-922X-0-4-1 through VB-922X-0-4-11

VB-9253-0-4-1 through VB-9253-0-4-11

VB-9263-0-4-1 through VB-9263-0-4-11

VB-9273-0-4-1 through VB-9273-0-4-11

VB-9283-0-4-1 through VB-9283-0-4-11

VB-931X-0-4-1 through VB-931X-0-4-11

VB-9323-0-4-1 throughVB-9323-0-4-11

Summary of content (2 pages)

PAGE 1
Valve-Actuator Linkage Kit HPO–5211/5212/5313 Mounting Installation Guide Linkage to Barber-Colman Valves 1. Thread 1/4-28 jam nut (1) onto valve stem (5) until 3/8" of valve stem is above the nut. 2. Thread stem extension (2) onto valve stem (5) and tighten against jam nut (1). 3. Thread nut (3) as far as possible onto stem extension (2). 4. Place flat washer (4) on top of nut (3) (on HPO–5211 and HPO–5212 linkage only). 5. Screw linkage (6) onto valve.
PAGE 2
Linkage to MEP–1200 Series Actuator Linkage to MEP–5000 Series Actuator 1. Rotate valve linkage lever (1) so that valve stem (and connecting rod) is in fully down position. 2. Depress disengagement button (5) on actuator and manually set pointer to the following position: • For 1/2" through 1-1/4" valves with HPO–5212 linkage, set pointer at third mark from full clockwise. • For 1-1/2" through 2" valves with HPO–5213 linkage, set pointer at second mark from full clockwise. 3.