Instructions / Assembly

ManualsBrandsKNAACK ManualsJobsite Boxes112

KNAACK® products are protected by one or more of the following patents or trademarks: U.S. - 6772613, 945736, 4288134, 4290281, 4383721, 5076078, 1182980, 1182981, 1182982, 1182983, 1266140, 1517767,

1560477, 1897535, 260062, 2290111; Canada - 1176681, 280058, 280798, 281398, 283281; U.K. - 2172510, 2233036, 1390299, 1392022; Australia - 754069, 754070; N.Z. - 296048, 296050; other patents pending.

NOTE: This lock system is designed to be used with a Master Lock®* No. 1, Master Lock No. 5 or American Lock®* No. 50, or an equivalent sized lock. If you

are using a padlock not listed above, it is your responsibility to make sure the lock mechanism is working correctly. Padlocks must meet ALL requirements

listed in Figure 2 or Figure 3.

TOOL REQUIRED - Ratchet Wrench with 1/2" Socket or 1/2" Combination Wrench

Master Lock® is a U.S. registered trademark of Master Lock Company.

American Lock® is a U.S. registered trademark of American Lock Company.

1. Unbolt the padlock tab using a 1/2" socket or wrench. Place the Latch Rod in "LATCHED" position as shown in Figure 1. Install 5/16" x 3/4" Carriage Bolt into correct

hole in Padlock Tab, install Padlock shackle into Padlock tab then secure to Lock Box using Locking Nut. See Figure 2 or 3.

TEST THE FUNCTION OF YOUR PADLOCK

(If you have installed one of the padlocks listed above per the instructions, you do not have to perform this test.)

2. Before locking the padlock, open cover and slide Latch Rod into "OPEN" position. If you are unable to move Latch Rod fully to "OPEN" position, the lock you have

installed is not acceptable for use, see note above.

3. Close the cover, move Latch Rod to "LATCHED" position. Lock padlock and try to move the Latch Rod to "OPEN" position and open the cover. If you are able to move

Latch Rod fully to "OPEN" position and open the cover, the lock you have installed is not acceptable for use, see note above.

INSTALLATION INSTRUCTIONS WATCHMAN® IV Lock System

DO NOT PAINT OVER OR REMOVE THIS DECAL

- NOTICE -

Any modification or unintended use of this product shall immediately

void all manufacturers warranties. Manufacturer disclaims all liability

for injuries to persons or property resulting from any modification to,

or unintended use of this product.

Figure 2.

Figure 3.

Use square

Hole for 5/16"

dia. shackle

(Master No. 1)

Use round Hole

for 3/8" dia.

shackle

(Master No. 5,

American No. 50)

For Installation of

Master Lock No. 1 or

equivalent size

For Installation of

Master Lock No. 5, American Lock No. 50

or equivalent size

Use top

hole only

Use top

hole only

Shackle

3/8" dia.

to 11/32"

dia.

1-3/16"

less

closed

1-7/16"

7/8" to

1-1/8"

7/8" to

1-1/8"

1-3/16"

Shackle

5/16"

dia.

or less

15/16" or

less

closed

or more

open

or more

open

FRONT CORNER OF BOX

Latch Rod

Padlock Tab

Padlock

Tab

Figure 1.

5/16" x 3/4"

Carr. Bolt

5/16" x 3/4"

Carr. Bolt

Locking

Nut

Locking

Nut

NOTE: Carriage Bolt will seat into

round hole when tightening

Locking Nut.

Lock Box

Lock

Box

2-1/4"

max.

2-1/4"

max.

SOLVENTS

GAS

GAS POWERED

EQUIPMENT

EXPLOSIVES

TANKS

 Do not put fuels, flammables, explosives or

hazardous materials inside these products.

 Gasoline, solvents, gun powder or other muni-

tions, dynamite, propane, acetylene or other

such products can explode if stored inside

these products.

 Use these products ONLY for storing and

transporting electric or hand tools and

equipment, and other similar materials.

 Failure to follow these warnings or modification

or other uses of these products could result in

death, serious injury or property damage.

Part No. 14-0008 REV. F ECN 5282 03/13

If you have any questions,

please call toll free at 1-800-456-7865.

Knaack LLC

ATTN: Warranty Claims

420 E. Terra Cotta Avenue

Crystal Lake, IL 60014