Installation Guide

ManualsBrandsKNAACK ManualsJobsite Boxes58

ASSEMBLY INSTRUCTIONS

STORAGEMASTER® Heavy-Duty Rolling Work Benches - Models 53 - 59 &

Model 62 WAR WAGON® Rolling Work Bench

Door Handle

5/16-18 Whiz

Lock Nut

Push Handle

5/16-18 x 3/4"

Truss Head Bolt

Hole Plugs

TOOLS REQUIRED

· Rubber Mallet

· 1/2" Socket (3/8" drive)

· 3/8" Medium Extension

· 3/8" Ratchet Wrench

· Screwdriver, common

· Screwdriver, phillips

PARTS LIST

· Work Bench Cabinet

· Handle Kit

5/16-18 x 3/4"

Truss Head Bolt

IMPORTANT

BEFORE YOU BEGIN

Read these instructions and

warnings completely before

installation.

Figure 1. Assembly View

WARNING

Black door knob must be

latched in the closed position

when moving this product, so

doors and drawers do not

open on inclines, which can

cause serious personal injury

or property damage.

62 HANDLE KIT

1 - Push Handle

6 - Door Handles

14 - 5/16-18 x 3/4" Bolt, Truss Hd.

12 - 5/16-18 Hex Whiz Nut

2 - Hole Plugs

2 - Lift Knob

DANGER

55-59 HANDLE KIT

1 - Push Handle

2 - Door Handles

6 - 5/16-18 x 3/4" Bolt, Truss Hd.

4 - 5/16-18 Hex Whiz Nut

2 - Hole Plugs

1 - Lift Knob

Caster Brakes are not suitable for

keeping units in place when trans-

porting. Secure by another method.

Do not use casters on rough or un-

even surfaces. Do not tow caster

mounted boxes.

 Do not put fuels, flammables, explosives or hazardous materials

inside these products.

 Gasoline, solvents, gun powder or other munitions, dynamite,

propane, acetylene or other such products can explode if stored

inside these products.

 Use these products ONLY for storing and transporting electric or

hand tools and equipment, and other similar materials.

 Failure to follow these warnings or modification or other uses of

these products could result in death, serious injury or property

damage.

CAUTION

Part No. 14-0046 REV. K ECN 5285 03/13

Summary of content (4 pages)

PAGE 1
ASSEMBLY INSTRUCTIONS STORAGEMASTER® Heavy-Duty Rolling Work Benches - Models 53 - 59 & Model 62 WAR WAGON® Rolling Work Bench Hole Plugs Push Handle 5/16-18 x 3/4" Truss Head Bolt Door Handle 5/16-18 x 3/4" Truss Head Bolt DANGER IMPORTANT BEFORE YOU BEGIN Do not put fuels, flammables, explosives or hazardous materials inside these products. Gasoline, solvents, gun powder or other munitions, dynamite, propane, acetylene or other such products can explode if stored inside these products.
PAGE 2
ASSEMBLY INSTRUCTIONS 1. Remove the handle kit from the cabinet. Attach the Door Handles (Figure 1.). Insert one Hole Plug into each end of the Push Handle then attach the handle to the end with the swivel casters. 2. Thread the black lift knob into the bottom of the slot in door centerpost. 3. WATCHMAN® III Lock System IMPORTANT: Carefully follow the separate instructions (see inside of door) which will guide you to a proper lock installation. #6 x 1/2" Screw 4. Remove the tape from the swivel casters.
PAGE 3
Lower Drawer Installation (six lower positions) 1. Take one heavy duty slide and insert rear clip into desired rear notch, and lower front clip into front notch (See Figure 3.). 2. To install a drawer, simply insert the drawer slide into the cabinet slide and close the drawer completely. The mechanism will automatically latch. DRAWER REMOVAL To remove a drawer, pull the drawer out until it stops. Notice the locking levers located inside the track that is attached to the drawer.
PAGE 4
KNAACK LLC LIMITED WARRANTY FOR KNAACK® PRODUCTS The following limited warranty applies to all KNAACK® branded products for the warranty period set forth below. If you have any questions or need assistance regarding the warranty of your product, please call our customer service department: (800) 456-7865, 8:00 am - 4:30 pm CST. KNAACK® Products - Limited Warranty Knaack LLC, located at 420 E.