PROJECTOR User’s Manual HDP2100 High Definition Projector
Copyright This publication, including all photographs, illustrations and software, is protected under international copyright laws, with all rights reserved. Neither this manual, nor any of the material contained herein, may be reproduced without written consent of the author. © Copyright 2010 Disclaimer The information in this document is subject to change without notice.
HDP2100 Users Manual Important Safety Information Important: It is strongly recommended that you read this section carefully before using the projector. These safety and usage instructions will ensure that you enjoy many years of safe use of the projector. Keep this manual for future reference. Symbols Used Warning symbols are used on the unit and in this manual to alert you of hazardous situations. The following styles are used in this manual to alert you to important information.
Preface Projector Installation Notice Place the projector in a horizontal position The tilt angle of the projector should not exceed 15 degrees, nor should the projector be installed in any way other than the desktop and ceiling mount, otherwise lamp life could decrease dramatically. Allow at least 50 cm clearance around the exhaust vent. Ensure that the intake vents do not recycle hot air from the exhaust vent.
HDP2100 Users Manual Replacing the Lamp Replacing the lamp can be hazardous if done incorrectly. See Replacing the Projection Lamp on page 30 for clear and safe instructions for this procedure. Before replacing the lamp: Unplug the power cord. Allow the lamp to cool for about one hour. Cleaning the Projector Unplug the power cord before cleaning. See Cleaning the Projector on page 32. Allow the lamp to cool for about one hour.
Preface Table of Contents GETTING STARTED .......................................................................................................................................................... 1 PACKING CHECKLIST ........................................................................................................................................................... 1 VIEWS OF PROJECTOR PARTS ................................................................................................................
HDP2100 Users Manual PROJECTION DISTANCE VS. PROJECTION SIZE ................................................................................................................... 39 HDP2100 Series Projection Distance and Size Table .................................................................................................. 39 HDP2100 SERIES TIMING MODE TABLE ...........................................................................................................................
HDP2100 Users Manual GETTING STARTED Packing Checklist Carefully unpack the projector and check that the following items are included: HDP2100 SERIES DLP PROJECTOR REMOTE CONTROL (WITH TWO AA BATTERIES) VGA CABLE COMPONENT CABLE POWER CORD HDMI CABLE CARRYING CASE CD-ROM (THIS USER’S MANUAL) WARRANTY CARD Contact your dealer immediately if any items are missing, appear damaged, or if the unit does not work.
HDP2100 Users Manual r Views of Projector Parts HDP2100 Series Front-right View ITEM LABEL DESCRIPTION 1. Height-adjuster button Push to release height adjuster 2. Height adjuster Adjusts level of projector 3. Lens Projection Lens 4. IR receiver Receive IR signal from remote control 5. Focus ring Focuses the projected image 6. Zoom ring Enlarges the projected image 7. Function keys See Top view—On-screen Display (OSD) buttons and LEDs.
HDP2100 Users Manual r Top view—On-screen Display (OSD) buttons and LEDs ITEM 1. LABEL (Power button) DESCRIPTION Turns the projector On or Off. SEE PAGE: 11 2. BLANK Displays a blank screen and mutes audio 3. ◄ (Left cursor) / Volume- Navigates and changes settings in the OSD Quick Menu – For Volume 4. Enter Enter or confirm highlighted OSD menu item 5. MENU Opens and exits OSD menus 6. ▲ (Up cursor) / Keystone+ Navigates and changes settings in the OSD Quick Menu – For Keystone 7.
HDP2100 Users Manual Rear view ITEM 1. LABEL AC IN Connect the POWER CABLE (USB) 2. DESCRIPTION SEE PAGE: 11 Connect the USB CABLE from a computer 3. COMPONENT IN Connect a component video enabled device 4. S-VIDEO IN Connect the S-VIDEO CABLE from a video device 5. VIDEO IN Connect the COMPOSITE CABLE from a video device 6. VGA IN Connect the RGB CABLE from a computer and components 7. HDMI – 1 Connect the HDMI CABLE from a HDMI device 8.
HDP2100 Users Manual Bottom view ITEM LABEL DESCRIPTION SEE PAGE: 13 1. Tilt adjustor Rotate adjuster lever to adjust angle position. 2. Ceiling support holes Contact your dealer for information on mounting the projector on a ceiling 3. Height adjustor Adjuster drops down when adjuster button is pushed. 4. Height adjustor button Push to release adjustor. 13 Note: When installing, ensure that you use only UL Listed ceiling mounts.
HDP2100 Users Manual Remote Control Parts Important: 1. Avoid using the projector with bright fluorescent lighting turned on. Certain high-frequency fluorescent lights can disrupt remote control operation. 2. Be sure nothing obstructs the path between the remote control and the projector. If the path between the remote control and the projector is obstructed, you can bounce the signal off certain reflective surfaces such as projector screens. 3.
HDP2100 Users Manual ITEM 1. 2. 3. 4. LABEL DESCRIPTION Power OFF Turns the projector off HDMI 2 Displays the HDMI 2 source selection S-VIDEO Displays the S-VIDEO source selection VIDEO Displays the VIDEO source selection Up cursor / Keystone+ Navigates and changes settings in the OSD Quick Menu – For Keystone 6. 7. 8. 9. 10. ENTER Enters and confirms settings in the OSD 5.
Remote Control Operating Range The remote control uses infrared transmission to control the projector. It is not necessary to point the remote directly at the projector. Provided you are not holding the remote perpendicular to the sides or the rear of the projector, the remote will function well within a radius of about 7 meters (23 feet) and 15 degrees above or below the projector level. If the projector does not respond to the remote control, move a little closer.
S ETUP AND O PERATION Inserting the Remote Control Batteries 1. 2. 3. Remove the battery compartment cover by sliding the cover in the direction of the arrow. Insert the battery with the positive side facing up. Replace the cover. Caution: 1. Only use AA batteries (Alkaline batteries are recommended). 2. Dispose of used batteries according to local ordinance regulations. 3. Remove the batteries when not using the projector for prolonged periods.
HDP2100 Users Manual Connecting Input Devices A PC or notebook computer and video devices can be connected to the projector at the same time. Video devices include DVD, VCD, and VHS players, as well as movie camcorders and digital still cameras. Check the user manual of the connecting device to confirm it has the appropriate output connector.
D DLLPP PPrroojjeeccttoorr –– U Usseerr’’ss M Maannuuaall Starting and Shutting down the Projector 1. 2. 3. Connect the power cord to the projector. Connect the other end to a wall outlet. The POWER LED will be on. Turn on the connected devices. Ensure the POWER LED displays a solid blue and not a flashing blue. Then POWER button to turn on press the the projector. The projector splash screen displays and connected devices are detected. 4.
HDP2100 Users Manual 5. When the POWER OFF window apon the control panel or pears, press on the remote control. The projector turns off. Caution: Do not unplug the power cord until the READY LED stops flashing–indicating the projector has cooled down.
HDP2100 Users Manual Adjusting the Projector Level Take note of the following when setting up the projector: • The projector table or stand should be level and sturdy. • Position the projector so that it is perpendicular to the screen. • Remove the Back Foot Holder on the rear adjuster foot before adjusting the projection angle. • Ensure the cables are in a safe location. You could trip over them. 1.
HDP2100 Users Manual Adjusting the Zoom ring, Focus and Keystone 1. 2. 3. Use the Image-zoom control (on the projector only) to resize the projected image and screen size B . Use the Image-focus control (on the projector only) to sharpen the projected image A . Use the KEYSTONE buttons (on the projector or the remote control) to correct image-trapezoid (wider top or bottom) effect. Remote control and OSD panel 4. The keystone control appears on the display.
HDP2100 Users Manual Adjusting the Volume 1. 2. 3. Press the Volume +/buttons on the remote control. The volume control appears on the display. Press the Left or Right Cursor buttons on the keypad to adjust Volume +/-. Press the MUTE button to turn off the volume (This feature is available only on the remote).
HDP2100 Users Manual O N -S CREEN D ISPLAY (OSD) M ENU S ETTINGS OSD Menu Controls The projector has an OSD that lets you make image adjustments and change various settings. Navigating the OSD You can use the remote control cursor buttons or the buttons on the top of the projector to navigate and make changes to the OSD. The following illustration shows the corresponding buttons on the projector. 1. To enter the OSD, press the MENU button. 2. There are six menus.
HDP2100 Users Manual Setting the OSD Language Set the OSD language to your preference before continuing. 1. Press the MENU button. Press the cursor ◄► button to navigate to SYSTEM SETUP: Basic. 2. Press the cursor ▲▼ button until Language is highlighted. 3. Press the cursor ◄► button until the language you want is selected. 4. Press the MENU button to close the OSD.
HDP2100 Users Manual OSD Menu Overview Use the following illustration to quickly find a setting or determine the range for a setting.
HDP2100 Users Manual PICTURE: Basic Menu Press the MENU button to open the OSD menu. Press the cursor ◄► button to move to the PICTURE: Basic menu. Press the cursor ▲▼ button to move up and down in the PICTURE: Basic menu. Press ◄► to change values for settings. Note: Customizeing the settings in PICTURE: Basic menu is only available in User 1/ 2/ 3 mode. ITEM DESCRIPTION Display Mode Press the cursor ◄► buttons to set the Display Mode.
HDP2100 Users Manual PICTURE: Advanced Menu Press the MENU button to open the OSD menu. Press the cursor ◄► button to move to the PICTURE: Advanced menu. Press the cursor ▲▼ button to move up and down in the PICTURE: Advanced menu. Press ◄► to change values for settings. ITEM DESCRIPTION Noise Reduction Press the cursor ◄► button to adjust the Noise Reduction. Color Temperature Press the cursor ◄► button to set the Color Temperature.
HDP2100 Users Manual HSG Adjustment Press the ENTER button to enter the HSG Adjustment sub menu. ITEM DESCRIPTION Primary Color Press the ◄► buttons to set the Primary Color. Notes: There are six sets (R/ G/ B/ C/ M/ Y) of colors to be customized. Hue Press the ◄► buttons to adjust the Hue. Saturation Press the ◄► buttons to adjust the Saturation. Gain Press the ◄► buttons to adjust the Gain.
HDP2100 Users Manual DISPLAY Menu Press the MENU button to open the OSD menu. Press the cursor ◄► button to move to the DISPLAY menu. Press the cursor ▲▼ button to move up and down in the DISPLAY menu. Press ◄► to change values for settings. ITEM DESCRIPTION Aspect Ratio Press the cursor ◄► button to set the Aspect Ratio. (Range: Auto/ 16:9/ 4:3/ Letter Box/ Real) Keystone Press the cursor ◄► button to adjust the Keystone.
HDP2100 Users Manual PC Detail Adjustment Press the ENTER button to enter the PC Detail Adjustment sub menu. Note: Customizing the settings in PC Detail Adjustment menu is only available when PC input source (analog RGB) is selected. ITEM DESCRIPTION Auto Press the ENTER/AUTO button on the control panel or the ENTER/AUTO button on the remote control to automatically adjust frequency, phase, and position. Frequency Press the ◄► buttons to adjust the A/D sampling number.
HDP2100 Users Manual SYSTEM SETUP: Basic Menu Press the MENU button to open the OSD menu. Press the cursor ◄► button to move to the SYSTEM SETUP: Basic menu. Press the cursor ▲▼ button to move up and down in the SYSTEM SETUP: Basic menu. Press ◄► to change values for settings. ITEM DESCRIPTION Language Press the cursor ◄► buttons to select a different localization menu.
HDP2100 Users Manual Menu Settings Press the ENTER button to enter the Menu Settings sub menu. ITEM DESCRIPTION Menu Position Press the ◄► buttons to select from five OSD locations: Top-Left/ Top-Right/ Center/ Bottom-Left/ Bottom-Right. Menu Display Time Press the ◄► buttons to set the Menu Display timer before the OSD times out. (Range: 5sec/ 10sec/ 15sec/ 20sec/ 25sec/ 30sec) Source Press the ENTER button to enter the Source sub menu.
HDP2100 Users Manual SYSTEM SETUP: Advanced Menu Press the MENU button to open the OSD menu. Press the cursor ◄► button to move to the SYSTEM SETUP: Advanced menu. Press the cursor ▲▼ button to move up and down in the SYSTEM SETUP: Advanced menu. ITEM DESCRIPTION Audio Press the ENTER button to enter the Audio sub menu. See Audio on page 27. Lamp Press the ENTER button to enter the Lamp sub menu. See Lamp on page 27. HDMI Press the ENTER button to enter the HDMI sub menu. See HDMI on page 28.
HDP2100 Users Manual Audio Press the ENTER button to enter the Audio sub menu. ITEM DESCRIPTION Volume Press the ◄► buttons to adjust the audio Volume. Bass Press the ◄► buttons to adjust the audio Bass. Treble Press the ◄► buttons to adjust the audio Treble. Mute Press the ◄► buttons to turn on or off the speaker. AGC Press the ◄► buttons to turn on or off the AGC setting. Reset Press the ENTER button to reset all settings to default values.
HDP2100 Users Manual HDMI Press the ENTER button to enter the HDMI sub menu. ITEM DESCRIPTION HDMI Format Press the ◄► buttons to select from three HDMI display formats: Auto/ PC signal/ Video signal. HDMI Amplifier Gain Press the ◄► buttons to adjust HDMI Amplifier Gain. Closed Caption Press the ENTER button to enter the Closed Caption sub menu. ITEM DESCRIPTION Closed Caption Enable Press the ◄► buttons to turn on or off Closed Caption.
HDP2100 Users Manual INFORMATION Menu Press the MENU button to open the OSD menu. Press the cursor ◄► button to move to the INFORMATION Menu. ITEM DESCRIPTION Source Displays the activated input source. Resolution Displays the native resolution of input source. Lamp Hour Displays the number of hours the lamp has been in use. Firmware Version Displays the firmware version of the projector. Note: Information displayed in this menu is for viewing only and cannot be edited.
HDP2100 Users Manual M AINTENANCE AND S ECURITY Replacing the Projection Lamp The projection lamp should be replaced when it burns out. It should only be replaced with a certified replacement part, which you can order from your local dealer. Important: a. The projection lamp used in this product contains a small amount of mercury. b. Do not dispose this product with general household waste. c. Disposal of this product must be carried out in accordance with the regulations of your local authority.
HDP2100 Users Manual 3. Remove the three screws from the lamp module. 4. Lift the module handle up. 5. Pull firmly on the module handle to remove the lamp module. 6. Reverse steps 1 to 5 to install the new lamp module. While installing, align the lamp module with the connector and ensure it is level to avoid damage. Note: The lamp module must sit securely in place and the lamp connector must be connected properly before tightening the screws.
HDP2100 Users Manual Cleaning the Projector Cleaning the projector to remove dust and grime will help ensure trouble-free operation. Warning: 1. Be sure to turn off and unplug the projector at least 30 minutes before cleaning. Failure to do so could result in a severe burn. 2. Use only a dampened cloth when cleaning. Do not allow water to enter the ventilation openings on the projector. 3.
HDP2100 Users Manual Using the Kensington® Lock If you are concerned about security, attach the projector to a permanent object with the Kensington slot and a security cable. Note: Contact your vendor for details on purchasing a suitable Kensington security cable. The security lock corresponds to Kensington’s MicroSaver Security System. If you have any comment, contact: Kensington, 2853 Campus Drive, San Mateo, CA 94403, U.S.A. Tel: 800-535-4242, http://www.Kensington.com.
HDP2100 Users Manual T ROUBLESHOOTING Common problems and solutions These guidelines provide tips to deal with problems you may encounter while using the projector. If the problem remains unsolved, contact your dealer for assistance. Often after time spent troubleshooting, the problem is traced to something as simple as a loose connection. Check the following before proceeding to the problem-specific solutions. • Use some other electrical device to confirm that the electrical outlet is working.
HDP2100 Users Manual LED Error Messages POWER LED BLINK READY LED BLINK TEMP LED BLINK Lamp Ready ON ON OFF Start ON OFF OFF Cooling ON FLASHING OFF Over temperature OFF OFF ON Thermal Break Sensor error 4 4 OFF Lamp End of lamp life detected 5 3 OFF Burner Fan error 6 1 OFF Lamp Fan error 6 2 OFF Power Fan error 6 3 OFF DMD Fan error 6 4 OFF Case Open 7 OFF OFF DMD error 8 OFF OFF Color wheel error 9 OFF OFF ERROR CODE MESSAGES In the event of an err
HDP2100 Users Manual Problem: The image is flat with no contrast Adjust the Contrast setting on the Image menu of the OSD. Problem: The color of the projected image does not match the source image. Adjust the Color Temperature and Gamma settings on the Image menu of the OSD. Lamp Problems Problem: There is no light from the projector 1. Check that the power cable is securely connected. 2. Ensure the power source is good by testing with another electrical device. 3.
HDP2100 Users Manual Audio Problems Problem: There is no sound 1. Adjust the volume on the remote control. 2. Adjust the volume of the audio source. 3. Check the audio cable connection. 4. Test the source audio output with other speakers. 5. Have the projector serviced. Problem: The sound is distorted 1. Check the audio cable connection. 2. Test the source audio output with other speakers. 3. Have the projector serviced.
HDP2100 Users Manual S PECIFICATIONS Specifications HDP2100 Series Model TI DLP DMD 0.65” Display type 1920 x 1080 Native Resolution 3.4 kg (7.5 lbs) Weight 1 meters ~ 10 meters Projection distance 25" ~ 300" Projection screen size Projection lens Manual Focus/Manual Zoom 1.
HDP2100 Users Manual Projection Distance vs.
HDP2100 Users Manual HDP2100 Series Timing Mode Table The projector can display several resolutions. The following table outlines the resolutions that can be displayed by the projector. RESOLUTION H-SYNC (KHZ) NTSC — 15.734 60.0 O — － － PAL/SECAM — 15.625 50.0 O — － － 720 x 400 37.9 85.0 — — O O 640 x 480 31.5 60.0 — — O O 640 x 480 37.9 72.8 — — O O 640 x 480 37.5 75.0 — — O O 640 x 480 43.3 85.0 — — O O 800 x 600 35.2 56.
HDP2100 Users Manual SIGNAL HDTV RESOLUTION H-SYNC (KHZ) V-SYNC COMPOSITE RGB HDMI COMPONENT (HZ) / S-VIDEO (ANALOG) (DIGITAL) 720p 37.5 50.0 — O — O 720p 45.0 60.0 — O — O 1080i 33.8 60.0 — O — O 1080i 28.1 50.0 — O — O 1080p 67.5 60.0 — O — O 1080p 56.3 50.0 — O — O O: Frequency supported —: Frequency not supported The native resolution of the panel for the HDP2100 series is 1920 x 1080.
HDP2100 Users Manual Projector Dimensions – 42 –
R EGULATORY C OMPLIANCE FCC Warning This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
