User's Manual

ManualsBrandsKnox ManualsElectronicsRadio Module

P a g e 1 | 7

User’s Manual

CC3100MODR11MAMOB Module

Revision History

9-2-2022 Rev 5

10-18-22 Rev 6: Corrected Molex Antenna from 1461530100 to 1461530200. Added missing Product

Attributes for Taiyo Yuden AH316M245001-T, Laird CAF94505 and Taoglas FXP 840.07.0055B.

10-20-22 Rev 7: Modified section “2.” to add antenna table listing host product family. Also added table

to “RF Exposure” statement.

10-21-22 Rev 8: Edited “Host Conditions” in antenna table and RF exposure statement per request.

1. Introduction

The CC3100MODR11MAMOB module allows for Wi-Fi 802.11b/g/n communications from Knox products

to connect with the KnoxConnect™ system using a Molex 1461530200, Laird CAF94505, Taoglas

FXP840.07.0055B, Air802 ANRD2405-RPSMA, Larsen NM05E2400B, or Taiyo Yuden AH316M245001-T

antenna. It is built from a standard networking component acquired from a large semiconductor

supplier to ensure a long-lifetime secure supply in support of Knox products.

This CC3100MODR11MAMOB module is placed into the product on whose labels state “This Device

Contains: FCC ID: 2AOVI-KNOX-RAS and IC: 23479-KNOXRAS”.

2. Use

NOTE: The CC3100MODR11MAMOB is certified to be used with the following antennas and product

families. The user is expected to operate it only in this fashion. Changes or modifications not

expressly approved by Knox Company voids the user’s authority to operate the equipment.

Antenna

Gain dBi

Host Conditions

Molex 1461530200

2.6

No host restriction

Laird CAF94505

2.0

Restricted to KeyDefender product family hosts.

Taoglas FXP840.07.0055B

3.3

Restricted to KeyDefender product family hosts.

Larsen NMO5E2400B

5.0

No host restriction

Air802, ANRD2405-RPSMA

5.0

No host restriction

Taiyo Yuden AH316M245001-T

1.9

No host restriction

The antennas have the following specifications:

Summary of content (7 pages)

PAGE 1
User’s Manual CC3100MODR11MAMOB Module Revision History 9-2-2022 Rev 5 10-18-22 Rev 6: Corrected Molex Antenna from 1461530100 to 1461530200. Added missing Product Attributes for Taiyo Yuden AH316M245001-T, Laird CAF94505 and Taoglas FXP 840.07.0055B. 10-20-22 Rev 7: Modified section “2.” to add antenna table listing host product family. Also added table to “RF Exposure” statement. 10-21-22 Rev 8: Edited “Host Conditions” in antenna table and RF exposure statement per request. 1.
PAGE 2
Molex 1461530200 Laird CAF94505 Page 2|7
PAGE 3
Taoglas FXP840.07.0055B The Air802 ANRD2405-RPSMA antenna has the following Specifications: Type External rubber ducky Gain 5 dBi Impedance 50 ohms Termination Reverse polarity SMA (RP_SMA) plug male connector on antenna, to RP_SMA female bulkhead connector, to U.FL connector, to the Printed Circuit Board Assembly.
PAGE 4
Taiyo Yuden AH316M245001-T This module complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This Class A digital apparatus complies with Canadian ICES-003. Cet appareil numerique de la classe A est conforme a la norme NMB-003 du Canada.
PAGE 5
indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. Concernant les EVMs avec antennes détachables Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d'un type et d'un gain maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada.
PAGE 6
conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. ** If the product is too small to include the above statement, it may be placed in the user’s manual. The following warnings must also be placed in the User Manual of the finished product using this module: This device complies with part 15 of the FCC Rules.
PAGE 7
For a Class B digital device or peripheral, place the following warning: Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.