EX-NEXT Manual

23
ICS setting changes can be performed using telemetry with
the radio (p.39) or by connecting directly to the Xpansion. The
Xpansion can be used for ICS setting changes only.
<ICS coresspondence servo>
for RSx/RSx2/RSx3/BSx2/BSx3 each series,
select "SERVO MOTOR SET"
<Serial coresspondence servo>
for 4S series,
select "SERIAL SERVO MOTOR SET".
MODEL
1.Select model memory of the servo.
Setting Range
MODEL: 1-5(default : 1)
2. Change ICS parameters. Each setting value is sent to the
servo when each data is changed, characteristics of the servo
will be changed. Please back up the default values by making
a memo.
*Please refer to P39 for parameters of the servo.
3. Please remove the battery for this function to exit.
MODEL
1.Select model memory of the servo.
Setting Range
MODEL: 1 to 5 (default 1)
2. Change ICS parameters. Each setting value is sent to the
servo when each data is changed, characteristics of the servo
will be changed.
Please back up the default values by making a memo.
3.Please remove the battery for this function to exit.
ID
ID of servo is changed.
Setting Range
ID: 1- 4 ( default 1)
LCDXpansion Unit2 EXP-201
Connecting receiver battery, ESC, etc
for power supply (Voltage 4.8 to 7.4v)
*This length is convenient as it will
be long enough to connect to the
transmitter.
●Setting changes of ICS correspondence servo -When connecting to Xpansion directly-
Extension Wire Black(High
current) 200mm
No.36520
No.10672
4S series
RSx/BSx series
Serial Correspondence servo
ICS Correspondence servo
Battery
Connecting First
Connecting last
Conecting Xpansion and Servo
*Please turn off transmitter when using this.
Select the type of servo and change settings.
*There is no operation
Servo Twin Extension Wire II
w/new plug
No.36509
TIMER タイマー
TIMER
OFF
OFF
TIMER START
TRG START
LAP HISTORY
START/STOP KEY
LAP KEY
SERVO MOTOR SET
SERIAL SERVO MOTOR SET
MASTER UPDATE
TIMER タイマー
TIMER
OFF
OFF
TIMER START
TRG START
LAP HISTORY
START/STOP KEY
LAP KEY
SERVO MOTOR SET
SERIAL SERVO MOTOR SET
MASTER UPDATE
TIMER タイマー
TIMER
OFF
OFF
TIMER START
TRG START
LAP HISTORY
START/STOP KEY
LAP KEY
SERVO MOTOR SET
STRCH1:
STRCH2:
SPEED:
PUNCH:
1
95
255
110
0
0
30
X8
MODEL:
DEADBAND:
DAMPING :
FREQUENCY:
TIMER タイマー
TIMER
OFF
OFF
TIMER START
TRG START
LAP HISTORY
START/STOP KEY
LAP KEY
SERIAL SERVO MOTOR SET
STRCH1:
STRCH2:
SPEED:
PUNCH:
1
95
255
110
0
0
30
X8
MODEL:
DEADBAND:
DAMPING :
FREQUENCY:
1
ID:
Case of connecting to B/S port of the KR-420XT,
please use the below settings.
ID1: Steering operation
ID2: Throttle operation
ID3: 3CH control
ID4: 4CH control
*ID5-8 can not be used. (As of Jan 2021)
P
Be sure to select the menu that corresponds to the servo you are
using. If you select the wrong menu, the servo will malfunction or
you will not be able to change the settings.
The initial value of the ICS setting differs depending on the servo
model and is not retained.It is recommended that you keep a
memo if necessary.
When data is not displayed normally and each parameter becomes 0
1) <ICS compatible servo> <Serial compatible servo> Check if there
is any mistake in the type.
2) Check the connection between the expansion and the servo (such
as the orientation of the connector when the tab is cut).
**ID5-8 are displayed but can not be used.