EX-NEXT Manual

33
START:POS1
3CHMODE:5WAY
KEY:ET3
+
ー
POS1:-100
POS2:-50
POS3: 0
POS4: 50
POS5:100
NOW:0
5WAY
Modify the 5-interval output settings.
Example
May be used for gear changing operations or when you wish to
set a 5-interval control scheme for the servo.
Example
Used when you want to use a Gyro system which the gain is
controlled by 3CH or 4CH.
How to set Gyro mode
Setting Range
START : POS1,POS2,POS3,POS4,POS5 (Default : POS3)
Sets the starting position.
KEY : OFF, ET1 - 5(Default : OFF)
Assigns a key to use for switching positions.
POS 1 : -100 - 100(Default : -100)
Sets Position 1's output position.
POS 2 : -100 - 100(Default : -50)
Sets Position 2's output position.
POS 3 : -100 - 100(Default : 0)
Sets Position 3's output position.
POS 4 : -100 - 100(Default : 50)
Sets Position 4's output position.
POS 5 : -100 - 100(Default : 100)
Sets Position 5's output position.
3-8CH
KEY :ET3
3CHMODE:ANALOG
REVERSE:NORM
+
ー
LOW:-100
CEN: 0
HIGH:100
STEP :5
NOW:0
100steps 100steps
2steps2steps
Operationposition
HIGHMaximum
Highposition
Movementrange
Center
LOWMaximum
Lowposition
ANALOG
GYRO
These settings are to enable continuous output for each
channnels.
This function modies the setting for gyro control.
Setting Range
KEY: OFF,ET1 - 5(Default : OFF)
Assigns a key to use for switching positions.
REVERSE : NOR
(normal)
, REV
(reverse)
(Default : NORM)
Sets operation direction.
STEP : 1 - 25(Default : 5)
Sets the amount of change for the operation.
Setting range
This is as same as Analog function.
KG-X
KR-212FHG
LOW
(low position)
- 100 - 0 (Default : - 100)
Sets the lowest value for the operation range.
CEN
(center position)
LOW - HIGH (Default : 0)
Sets the neutral position for the operation range.
HIGH
(high position)
0 -100 (Default : 100)
Sets the highest value for the operation range.
How to Use Analog Settings
Low Position Side :
Between LOW and CEN are 100 steps within which the intervals can be
adjusted.
High Position Side :
Between CEN and HIGH are 100 steps within which the intervals can be
adjusted.
Center position is the staring position.
P
Low/High positions cannot be exceeded. Operations
which try to do so will stop just before the Low/High
positions.
P
Example) When STEP value is 2
When LOW side is set to 5 intervals.
When HIGH side is set to 4 intervals.
If set Gyro mode in the 3ch or 4ch, both channel will be set to the
Gyro mode.
When the 3ch/4ch mode is changed from GYRO mode to another
mode or OFF, the ET3 and ET5 will return to the setting for (OFF).
Please notice ET3 are not return to the default value(T: BRAKE).
Please prepare the gyro system (ex. KR-212FHG,KG-X)
separately. The gyro effect is not provided only in the main system
of transmitter.
The current output position is displayed by “NOW”
and shown on the bar graph.
P
The current output position is displayed by “NOW”
and shown on the bar graph.
P
ET3 : 3ch control (Steering gyro gain control)
ET5 : 4ch control (Throttle gyro gain control)
Adjust it to moderate gyro gain while running.
Using 3ch or 4ch.
The setting is forcibly as follows by Gyro mode.
3-8CH
3-8CH
3

・
4CH