EX-NEXT Manual

35
3-8CH
->KEY:OFF
TRIM0
BRAKE100
THHOLD0
HIPOINT 100
REVERSENORM
MODENORMAL
->KEY:OFF
->KEY:OFF>>>
->KEY:OFF
->KEY:OFF
3CHMODE：AMP
ETMODESET
3CHMODE:AMP
NORMAL:
BURN ：ON
DIG ：ON
＜＜＜
F HOLD：ON
ON
R HOLD：ON
AMP Mixing MODE
Used when the front and rear wheels are controlled by
separate ESCs and motors. If 3CH or 4CH is set to the front-
wheel drive function, it will operate in conjunction with 2CH's
throttle operations.
Setting range
MODE Default: NORMAL
NORMAL : drives both front and rear wheels
BURN : drives rear wheels only
DIG : drives front wheels only
F HOLD : drives front wheels at a set speed
R HOLD : drives rear wheels at a set speed
TH HOLD : -100 : 100 (Default: 0)
This function adjusts the set speed used for (F HOLD) and (R
HOLD) selected in Amp Mixing Mode. [F HOLD] adjusts the
front wheel drive while [R HOLD] adjusts the rear wheel drive.
HIPOINT : 0 - 150 (Default : 100)
Adjusts the maximum amount of throttle to be applied to the
front wheels. Equivalent to the [Throttle High Point] function.
*This setting is activated when F HOLD or R HOLD mode is
selected.
TRIM : -50 - 50 (Default: 0)
Adjusts the neutral position of the front wheels.
REVERSE : NORM,REVS (Default: NORM)
Changes the movement direction of the front wheels.
MODE → KEY : OFF,ET1 - 5 (Default: OFF)
Assigns ET or BT keys to activate the various front wheel
drive modes.
TH HOLD → KEY : OFF, ET1 - 5 (Default: OFF)
Assigns ET keys to be used for the set speed used for TH
HOLD.
HIPOINT → KEY : OFF,ET1 - 5 (Default: OFF)
Assigns ET or BT keys to adjust HIPOINT value.
BRAKE → KEY : OFF, ET1 - 5 (Default: OFF)
Assigns ET or BT keys to adjust BRAKE value.
REVERSE → KEY : OFF, ET1 - 5 (Default: OFF)
Assigns ET or BT keys to changes the movement direction of
the front wheels.
BRAKE : 0 - 150 (Default: 100)
Modify the maximum amount of reverse (brake) to be applied to
the front wheels. Equivalent to [Throttle Brake] function.
*This setting is activated when NORMAL, DIG, or R HOLD
mode is selected.
Setting Range
ET MODE SET
Assigns ET or BT keys to activate the various front
wheel drive modes.
NORMAL : ON, OFF (Default: ON)
BURN : ON, OFF (Default: ON)
DIG : ON, OFF (Default: ON)
F HOLD : ON, OFF (Default: ON)
R HOLD : ON, OFF (Default: ON)
Example Use Rock crawling car etc.
This makes it easy to adjust the amount of maximum throttle,
particularly on a glow engine car.
The setting position cannot exceed what is set by [High
Point] or [Brake].
Assigning these keys may be convenient for rock crawlers or when
you need to adjust Amp Mixing settings.
For electric cars, the throttle is set by the ESC so there is no need
to set this function. However, some older ESCs will not function
properly unless reverse is also set.
P
P
P
P
If the amp mixing high point is set low and the amp mixing trim
is set to a high value toward acceleration, the resulting throttle
movement may be extraordinarily small.
P
On glow engine cars, an overly high setting value will
increase load on the servo and lead to it being damaged.
Check carefully while adjusting.
On glow engine cars, an overly high setting value will
increase load on the servo and lead to it being damaged.
Check carefully while adjusting.
On electric cars, a setting value that is too small may cause
problems with the ESC settings. Make adjustments starting
from the default setting (100).
On electric cars, a setting value that is too small may cause
problems with the ESC settings. Make adjustments starting
from the default setting (100).
Brake will not operate if the value is set to 0.
Brake will not operate if the value is set to 0.
3

・
4CH