EX-NEXT Manual

43
SPURGEAR
PINIONGEAR
ｽﾊﾟｰ
TRANSRATIO
/ﾋﾟﾆｵﾝ
x2ｼﾞｹﾞﾝｿｸ
30
2.00
110
RATIO
FINAL
ｷﾞﾔﾋ
7.333
CULCULATORケイサンキ
6385*($5
3,1,21*($5
75$165$7,2



),1$/

&$/&8/$725
7,5(',$0(7(5

00
52//287

BUZZERTONE
ﾊﾟﾀｰﾝ
ﾎﾞﾘｭｰﾑ
1
5
2
BUZZERPATTERN
ｵﾝﾃｲ
BUZZERVOLUME
ＳＯＵＮＤ サウンド
BUZZER TONE
1
5
5
ON
2
BUZZER PATTERN
BUZZER VOLUME
VIBRATOR POWER
POWER ON VIBRATOR
ＳＯＵＮＤ
CALCULATOR
SOUND
VR INFORMATION
You can calculate the gear ratio.
You can make sound-related settings.
Do not touch the steering wheel or throttle trigger when entering
this menu and finally pressing the ENT key. An abnormal value
may be entered, which may cause inconvenience in subsequent
operations.
The period during which this operation is required varies greatly
depending on the frequency of use and the operation method. If
the inconvenience persists even after performing this function,
please contact our service department.
If the brake lever of the throttle trigger is opened too much, the
brake lever may interfere with the case and may not complete
normally. In this case, readjust the brake lever and then set the VR
information again.
SYSTEM
Setting Range
SPUR GEAR: 1 to 999 (Default : 110)
PINIONGEAR: 1 to 999 (Default : 30)
TRANSRATIO: 1.00 to 99.99 (Default : 2.00)
TIRE DIAMETER Tire diameter: 0.00 to 200.99 (Default : 63.00)
Setting Range
BUZZER TONE
(Buzzer pitch setting) 1 to 7 ( Default : 2)
BUZZER PATTERN
(Buzzer pattern setting) 1 to 7 ( Default : 1)
BUZZER VOLUME
(Buzzer volume setting) 0 to 5 ( Default : 5)
VIBRATOR POWER
(Vibrator power setting) OFF ~ 5 ( Default : 5)
VIBRATOR TIME
(Vibrator time setting) 1 to 6 ( Default : 5)
VIBRATOR PATTERN
(Vibrator pattern setting) 0 to 6 ( Default : 2)
How to use
When you enter the spur, pinion, and the transmission ratio; the
calculations are automatic and displayed on the right side of the
screen.
This function sets the position information of the CPU, steering
and throttle of this unit.
* Be sure to make the settings.
○ When using this unit for the rst time
○ When the steering unit / grip unit is replaced with another
product or returned to its original position
○ When the adjustment of the deangle adjustment of the
handle is changed
○ When the location information is out of order due to
exhaustion during use
1. Select FUNCTION on the initial screen and
press the ENT key.
2. Select SYSTEM in the setting and press the ENT
key.
3. Select your system's VRINFO and press the
ENT key.
5. If you slowly move the throttle trigger forward /
backward to the end, the value will change, so
release the trigger to put it in the neutral state.
6. If the operations of 4 and 5 are normal, "YES" on
the right side of the screen will be activated, so
conrm with the ENT key.
If the values differ signicantly,
readjust the adjustment screw of the
deangle adjustment adjuster, and
then set the VR information again.
When the number is
small…loosen
When the number is
large... tighten
4. Slowly turn the steering wheel left and right to
the end to change the value. Release the wheel
to put it in the neutral state.
* If you press the BACK key during operation, it will be canceled.
ST-LEFT
2078
2
ﾋﾀﾞﾘ
RIGHT
ﾐｷﾞ
NUT
ｾﾝﾀｰ
TH-HI
ｾﾞﾝｼﾝ
LOW
ﾌﾞﾚｰｷ
NUT
ｾﾝﾀｰ
2075
2072
OK?
YES
2198
2204
2194
VRINFOMATION VRｲﾝﾌｫﾒｰｼｮﾝ
ST- LEFT
RIGHT
NUT
TH- HI
LOW
NUT
OK?
YES
ｘｘｘｘ
ｘｘｘｘ
ｘｘｘｘ
ｘｘｘｘ
ｘｘｘｘ
ｘｘｘｘ
VR INFOMATION
Right
Maximum
Left
Maximum
Maximum
Forward
Maximum
Reverse
ST- LEFT
RIGHT
NUT
TH- HI
LOW
NUT
1 7 6 0
◇
-1 7 5 2
1 2 8 6
◇
- 5 9 9
VR INFOMATION
OK?
YES
When adjusting and changing the deangle adjustment of
the handle, set so that the values of ST-LEFT and RIGHT
do not differ signicantly.
P