Expert Grip Unit LDT - Manual

This function is for setting the steering and throttle position
information to the transmitter (calibration).
When changing the Grip Unit.
After a long period of usage and it has wrong location data
due to exhaustion of parts.
1,Please press the enter key after selecting the
Function( Setting) in the initial screen.
2,Please press the enter key after selecting the
SYSTEM in the Setting.
3,Please press the enter key after selecting the
VR INFO in the SYSTEM.
4,Values in the screen will be changed when
turning the steering wheel slowly to the right and
the left to full lock. Please release wheel back to
neutral.
5,Values in the screen will be changed when
slowly operating the throttle trigger to pull and
push to full throw. Please release throttle trigger
back to the neutral.
6,If steps 4 and 5 are successful, "YES" on the
right of the screen will be highlighted, press enter
to confirm.
If you press "Back" during the operation, this
operation will be canceled.
1, Open battery cover and connect the battery for the
transmitter to the connector.
Setting the Trigger position
Adjust to the position where you can operate comfortably,
according to the size of your palm and the length of your
finger.
1. Adjust to the position where you can operate comfortably,
according to the size of your palm and the length of your finger.
Please adjust to the position of your index finger. We
suggest the tip of your finger to the curved portion of
the throttle lever.
Adjustment of Finger hold cover.
You can adjust to the default of +5mm by change
the position and the combination of the spacers.
Best adjustment position is when your index finger
nail does not touch the lever when moved and
having the most narrow position as possible.
Adjustment of trigger tension.
Adjust the tension from the side of the trigger unit
using a 1.5mm hexagon wrench.
Strong tension by tightening clockwise, less tension
by loosening counterclockwise.
If the tension is too loose, it breaks out from the
unit. Please take notice.
Install the thinner PAD to the throttle lever and the
thicker Pad to the Finger hold cover. You can hold the
trigger with less effort to prevent fatigue and have
delicate, precise control.
Please adjust the install position and the size of
PAD to your preference.
Please use all the spacers (total 5mm).
If you can not use all of the spacers, the trigger
base maybe be broken.
Setting of Volume Information Adjustment of LDT Trigger Unit
You must perform this setting.
Hex wrench is not included.
Example of the screen before setting
*This is an example using the EX-RR/EX-2.
Right
Maximum
Maximum
Maximum
Left
Maximum
Forward
Reverse
Charging connector
holder
M3 Nut
Trigger Base
Throttle lever
(default)
Throttle lever
thinner PAD
Move the spacer
fit to the size of finger.
Finger hold cover
t=2mm
Spacer(black)
t=1mm
Spacer(white)
M3-14 Cap bolt
(2mm hexagonal)
Charging connector cover
Charging connector holder
Charging connector
Balance terminal
extension cable
Finger hold cover
thicker Pad
Connector
When using a battery that is for the transmitter.
2,Please install charging connector to charging connector holder.
3,Please insert battery and set the battery cover.
4,Charging method
(Sold separately or like same own)
Please use our genuine charger/cable for charging
No.55056
Conversion cable for Charging(for XH connector)
Be sure to turn off the power when charging.
Change to width type Throttle lever.
Installation of the Trigger pad.
You can change to a wide type throttle lever for fit to
your finger width.
NormalWide
*Please repeat the adjustments to where you feel comfortable.
Please tighten the screw with adequate torque.
There is no problem if the value is different from the above figure.
Please tighten the screws with adequate torque.
Please check the battery mode in the transmitter
and choose correct battery.
*Please refer manual for how to setting.
Charger