KOALA KARE PRODUCTS Installation and Operation Instructions KB100 Baby Changing Station Cambiador Plegable Table à Langer Babywickeltisch Your unit can be installed to meet ADA regulations when and where applicable. Refer to Federal Register, Volume 56, No 144 28 CFR Part 36. You are responsible for the safe operation of this unit. IMPORTANT. RETAIN FOR FUTURE REFERENCE. READ CAREFULLY. IMPORTANTE. GUÁRDELO PARA FUTURAS CONSULTAS. LEER ATENTAMENTE. IMPORTANT. À CONSERVER POUR INFORMATION.
OPERATING INSTRUCTIONS Please Note: To assure proper installation, it is suggested that a qualified person or carpenter install the Koala Kare Baby Changing Station. Koala Kare Products will not be responsible if the station is not installed properly. Koala Kare Baby Changing Stations have been tested to hold a substantial static load. The unit must be attached to a permanent wall that is capable of holding a substantial load.
INSTALLATION INSTRUCTIONS Horizontal Baby Changing Station Surface Mounted Model Number KB100 and KB110-SSWM Step 1. Remove changing station from the shipping container and check for any freight damage. Identify the best location for installing the unit. Hold the unit in place and open the bed. Make sure you have taken the operating clearance into consideration. Step 2. Based upon the type of wall on which you will be mounting the station, determine the best method of mounting.
INSTALLATION INSTRUCTIONS Step 4. Find the stud where you will be attaching the left side of the changing station to the wall. Measure up from the floor 44” (1118 mm), at the center of the stud and mark the wall. Mark holes using a level and measuring tape to make sure holes are precisely positioned. Hold unit in place to check. Use a 1/8” drill bit to make pilot holes and the four ¼” x 3” panhead screws with washers (supplied) to attach the unit to the wall studs.
ASTM F 2285-04 WARNING: Never leave child unattended. WARNING: Avoid serious injury from falling or sliding out. Always use restraint system. WARNING: Designed for Infants Only. Age up to 3.5 years and weighing less than 50 lbs. Keep one hand on the child at all times. Parcels or accessory items, or both, placed on the unit may cause the unit to become unstable. WARNING WARNING WARNING WARNING Never leave child unattended. Avoid serious injury from falling or sliding out. Always use restraint system.
EN 12221:2008 ATTENTION : Ne laissez pas l’enfant sans surveillance. WARNING: Do not leave the child unattended. Tous les éléments d’assemblage doivent être All assembly fittings shall always be correctly correctement fixés et vérifiés régulièrement. tightened and checked regularly.
INSTRUCCIONES DE USO Atención: Para garantizar una instalación correcta, se sugiere que una persona capacitada o un carpintero instale el cambiador de pañales Koala Kare Baby. Koala Kare Products no se responsabilizará si el cambiador no se ha instalado adecuadamente. El cambiador de pañales Koala Baby Changing Station se ha probado para garantizar que soporta un peso estático considerable. La unidad debe anclarse en una pared fija capaz de soportar un peso considerable.
INSTRUCCIONES DE INSTALACIÓN Cambiador montado en superficie horizontal Número de modelo KB100 and KB110-SSWM Paso 1. Saque la base para cambio de pañales de la caja de embalaje y compruebe que no haya aufrido daños durante el transporte. Determine la ubicación óptima para la instalación de la base para cambio de pañales. Sujete la unidad en su sitio y abra la cama. Recuerde que debe disponer de espacio suficiente para manipular la unidad. Paso 2.
INSTRUCCIONES DE INSTALACIÓN Paso 4. Localice el montante que unirá el lateral izquierdo de la base para cambio de pañales a la pared. Mida desde el suelo 1118 mm (44”), en el centro del montante, y haga una marca en la pared. Señale de orificios con un nivel y una cinta métrica para asegurarse de que estén ubicados en el lugar exacto. Sujete la unidad en su sitio para realizar la comprobación.
MODE D’EMPLOI Remarque : La table à langer Koala Kare doit être installée par une personne qualifiée ou un menuisier afin de garantir une installation correcte. Koala Kare Products ne pourra être tenu responsable si la table n’est pas bien installée. Les tables à langer Koala Kare ont été testées pour supporter une charge statique importante. La table à langer doit être fixée à un mur permanent pouvant supporter un poids important.
INSTALLATION Table à langer horizontale montée en surface Référence modèle KB100 and KB110-SSWM Étape 1. Retirez la table à langer du carton d’emballage et vérifiez qu’elle n’a pas été endommagée durant le transport. Identifiez le meilleur endroit pour l’installer. Tenez la table à langer en place et ouvrez le lit. Assurez-vous que vous avez pris les jeux de fonctionnement en considération. Étape 2.
INSTALLATION Étape 4. Localisez le poteau sur lequel vous fixerez le côté gauche de la table à langer au mur. Mesurez à partir du sol 1118 mm (44”), au centre du poteau, et faites un repère sur le mur. Marquez les trous à l’aide d’un niveau et du mètre pour vous assurer que les trous sont positionnés avec précision. Tenez la table à langer en place pour vérification.
GEBRAUCHSANLEITUNG Bitte beachten: Um die sachgerechte Montage der Koala Kare Babywickelstation zu gewährleisten, empfehlen wir, diese Tätigkeit von einer Fachkraft bzw. einem Tischler ausführen zu lassen. Koala Kare Products haftet nicht bei Schäden, die durch die unsachgemäße Montage der Wickelstation entstehen. Koala Kare Babywickelstationen wurden mit erheblicher statischer Last getestet. Das Produkt muss an einer festen Wand montiert werden, die für eine erhebliche Belastung geeignet ist.
MONTAGEANLEITUNG Horizontale Babywickeltisch für Aufbaumontage Modellnummer KB100 and KB110-SSWM Schritt 1. Nehmen Sie die Wickelstation aus dem Versandkarten und prüfen Sie das Produkt auf Transportschäden. Ermitteln Sie den geeigneten Ort für die Montage der Babywickelstation. Halten Sie das Produkt an den vorgesehenen Montageort und öffnen Sie die Liegefläche. Stellen Sie sicher, dass der für den Gebrauch erforderliche Platz vorhanden ist. Schritt 2.
MONTAGEANLEITUNG Schritt 4. Lokalisieren Sie den Ständer, an dem Sie die linke Seite der Wickelstation befestigen wollen. Messen Sie vom Boden ausgehend mittig 1,118 mm (44”), auf dem Ständer und markieren Sie die entsprechende Stelle an der Wand. Kennzeichnen Sie die übrigen Bohrstellen mit Hilfe von Wasserwaage und Maßand, damit die Markierungen für die Bohlöcher exakt positioniert sind. Halten Sie das Produkt zur Überprüfung an die vorgesehene Stelle.
PN 342 August 2012